Panasonic DMR-E85H operating instructions Specifications, Safety precautions

Page 45

Specifications

Recording system DVD Video Recording format (DVD-RAM), DVD-Video format (DVD-R)

Recordable discs

DVD-RAM: 12 cm 4.7 GB, 12 cm 9.4 GB, 8 cm 2.8 GB

12cm 4.7 GB (Ver. 2.1/3k-SPEED DVD-RAM Revision 1.0) DVD-R: 12 cm 4.7 GB, 8 cm 1.4 GB (for General Ver. 2.0)

12 cm 4.7 GB (for General Ver. 2.0/4k-SPEED DVD-R Revision 1.0)

Recording timeMaximum 8 hours (with 4.7 GB disc) XP: Approx. 1 hour, SP: Approx. 2 hours

LP: Approx. 4 hours, EP: Approx. 6 hours/8 hours Maximum 142 hours (with built-in 80 GB HDD)

XP: Approx. 17 hours, SP: Approx. 34 hours

LP: Approx. 68 hours, EP: Approx. 106 hours/142 hours

Playable discs

DVD-RAM: 12 cm 4.7 GB, 12 cm 9.4 GB , 8 cm 2.8 GB

12cm 4.7 GB (Ver. 2.1/3k-SPEED DVD-RAM Revision 1.0) DVD-R: 12 cm 4.7 GB, 8 cm 1.4 GB (for General Ver. 2.0)

12cm 4.7 GB (for General Ver. 2.0/4k-SPEED DVD-R Revision 1.0) DVD-Video, DVD-Audio, Video CD, CD-Audio (CD-DA)

CD-R/RW (MP3, CD-DA, Video CD formatted discs)

Built-in HDD capacity

80 GB

Drive unit

High Speed Drive (correspond to 4 times speed with

 

DVD-R disc and 3 times speed with DVD-RAM disc.)

LASER specification

Class I LASER Product (Pickup)

Wave length:795 nm, 658 nm Laser power:

No hazardous radiation is emitted with the safety protection

NORSK

 

 

Bølgelengde:

 

795 nm, 658 nm

Laserstyrke:

 

Ingen farlig stråling sendes ut

Audio

 

 

Recording system:

Dolby Digital 2ch, Linear PCM (XP mode, 2ch)

Audio in:

 

AV1/AV2 (21 pin), AV3/AV4 (pin jack)

Input level:

Standard: 0.5 Vrms, Full scale: 2.0 Vrms at 1 kHz

Input impedance:

 

More than 10 k≠

Audio out:

 

AV1/AV2 (21 pin), Audio Out (pin jack)

Output level:

Standard: 0.5 Vrms, Full scale: 2.0 Vrms at 1 kHz

Output impedance:

Less than 1 k≠

Digital audio out: Optical terminal (PCM, Dolby Digital, DTS, MPEG)

Television system

Tuner system

 

Channel coverage

 

 

 

PAL-BGH

VHF:

E2–E12, A–H2 (Italy)

SECAM-BG

UHF: 21–69

(CCIR)

CATV: S01–S05 (S1–S3),

 

 

S1–S20 (M1–U10), S21–S41

 

 

 

SECAM-L, L’

VHF:

2–10

(France)

UHF:

21–69

 

CATV: B–Q (100.5–299.5 MHz),

 

 

S21–S41 (299.5–467.25 MHz)

 

 

 

RF converter output:

 

Not provided

Video

Video system:

SECAM (only input)/PAL colour signal, 625 lines, 50 fields NTSC colour signal, 525 lines, 60 fields

Recording system:MPEG2 (Hybrid VBR) Video in (SECAM/PAL/NTSC):

AV1/AV2 (21 pin), AV3/AV4 (pin jack) 1 Vp-p 75 ≠, termination S-Video in (SECAM/PAL/NTSC):

AV2 (21 pin), AV3/AV4 (S terminal) 1 Vp-p 75 ≠, termination RGB in (PAL):

AV2 (21 pin) 0.7 Vp-p (PAL) 75 ≠, termination Video out (PAL/NTSC):

AV1/AV2 (21 pin), Video Out (pin jack) 1 Vp-p 75 ≠, termination S-Video out (PAL/NTSC):

AV1 (21 pin), S-Video Out (S terminal) 1 Vp-p 75 ≠, termination RGB out (PAL/NTSC):

AV1 (21 pin) 0.7 Vp-p (PAL) 75 ≠, termination

Component video output (NTSC 480P/480I, PAL 576P/576I)

Y: 1.0 Vp-p 75 ≠, termination PB: 0.7 Vp-p 75 ≠, termination PR: 0.7 Vp-p 75 ≠, termination

Others

 

Region code:

‚ 2

Operating temperature:

5–40 oC

Operating humidity range:

10–80 % RH (no condensation)

Power supply:

AC 220–240 V, 50 Hz

Power consumption:

38 W

Dimensions (WkDkH):

Approx. 430k274k79 mm

Mass:

Approx. 4.4 kg

 

Power consumption in standby mode:

 

Approx. 3 W (Power Save mode)

 

 

[Note]

Specifications are subject to change without notice. Mass and dimensions are approximate.

Reference

Safety precautions

Placement

Set the unit up on an even surface away from direct sunlight, high temperatures, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the unit’s service life.

Do not place heavy items on the unit.

Voltage

Do not use high voltage power sources. This can overload the unit and cause a fire.

Do not use a DC power source. Check the source carefully when setting the unit up on a ship or other place where DC is used.

AC mains lead protection

Ensure the AC mains lead is connected correctly and not damaged. Poor connection and lead damage can cause fire or electric shock. Do not pull, bend, or place heavy items on the lead.

Grasp the plug firmly when unplugging the lead. Pulling the AC mains lead can cause electric shock.

Do not handle the plug with wet hands. This can cause electric shock.

Foreign matter

Do not let metal objects fall inside the unit. This can cause electric shock or malfunction.

Do not let liquids get into the unit. This can cause electric shock or malfunction. If this occurs, immediately disconnect the unit from the power supply and contact your dealer.

Do not spray insecticides onto or into the unit. They contain flammable gases which can ignite if sprayed into the unit.

Service

Do not attempt to repair this unit by yourself. If sound is interrupted, indicators fail to light, smoke appears, or any other problem that is not covered in these instructions occurs, disconnect the AC mains lead and contact your dealer or an authorized service center. Electric shock or damage to the unit can occur if the unit is repaired, disassembled or reconstructed by unqualified persons.

Extend operating life by disconnecting the unit from the power source if it is not to be used for a long time.

RQT7664

45

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Example Ejemplo Operating Instructions Instrucciones de funcionamientoStarted Useful features Table of contentsRemote control AccessoriesPlease check and identify the supplied accessories BatteriesControl reference guide Remote controlMain unit Unit’s displayWhen the unit is not to be used for a long time Recommended connection for your televisionDo not connect the unit through a video cassette recorder AV1 terminal Connecting a television with 21-pin Scart terminal and VCRComponent video output ConnectionVideo OUT terminal Component Video OUT terminalConnecting an amplifier or system component To enjoy multi-channel surround sound on DVD-VideoConnection to a stereo amplifier If the clock setting menu appears Preset Download Setup with Q Link functionsEnter ReturnCountry setting menu appears Auto-Setup Setup without Q Link functionsAuto-Setup starts. This takes about 8 minutes Auto-Setup is complete when you see the television pictureSelecting television type and aspect Press 3, 4, 2, 1 to select Setup and press EnterPress Functions To enjoy progressive videoPoint the remote control at the television When the following indicator appears on the unit’s displayTo change the code on the remote control Television operationHDD and discs you can use for recording and play HDD and Disc informationPlay-only discs 12 cm/8 cm Discs that cannot be playedGetting HDD Hard disk drive handling careRecording television programmes Press W X CH to select the channelPress ¥ REC to start recording Recording modes and approximate recording times Playing while you are recordingDirect TV Recording Recording from an external equipment Flexible RecordingUsing Showview number to make timer recordings Timer recordingPress F Timer Press ShowViewPress 3, 4 to select New Timer Manually programming timer recordingsPress PROG/CHECK Press 1 to move through the itemsLinked timer recordings with external equipment EXT Link Check, change or delete a programmePress EXT Link Playing discs BackPlaying Skipping the specified Operations during playTime Time Slip Manual SkipChanging audio Editing operations during playPress Audio Press Erase Press 2, 1 to select Erase and press EnterUsing the tree screen to find a group Using menus to play MP3Press 3, 4, 2, 1 to select a group Press TOP MenuDisc menu-Setting the disc content Using on-screen menus and Status messagesOn-screen menus Press DisplayPress Status Status messagesPlay menu-Change the play sequence Picture menu-Change the picture qualityEditing titles/chapters and playing chapters Editing titles/chaptersPress Direct Navigator Press 3, 4, 2, 1 to select the title Press 3, 4, 2, 1 to select the chapterTitle operations Set up Protection §Press 2, 1 to select Yes and press Enter Press Enter at the start point and endCreating, editing and playing play lists Press 3 to cancelPress 3, 4, 2, 1 to select Play List and press Enter Creating play listsPlay list operations Editing and playing play lists/chaptersMove ChapterShow Enter Name screen Entering textPress 3, 4 To select a Character and press Enter Press SETTransfer Dubbing Transferring dubbing titles or play listsPress Dubbing One Touch Transfer dubbingPress Enter to confirm DubbingTransferring dubbing a finalized DVD-R Press 3, 4 to select Start Dubbing and press EnterTo edit the transferring dubbing list DubbingPress 3, 4, 2, 1 to select an item and press Enter Functions windowPress 3, 4, 2, 1 to select Disc Management and press Enter Press 3, 4 to select the operation and press EnterTop Menu Disc NameDisc Protection Format DiscCommon procedures Changing the unit’s settingsSummary of settings Convenient functionsPicture Tabs Menus Options Underlined items are the factory presetsFunctions TV Aspect AV2 SettingsProgressive TV SystemPress 3, 4 to select Manual and press Enter TuningPress 3, 4, 2 Programme positionTo change the setting all at once PAL!#NTSC Auto-Setup RestartPress 3, 4, 2, 1 to select a country and press Enter TV SystemChild Lock Clock settingsSafety precautions SpecificationsGlossary When programming When ShowviewLink Message Message appears whenSet upPage Frequently asked questionsCover RecordingError messages On the televisionOn the unit’s display Following do not indicate a problem with this unit Troubleshooting guideBreaks ≥Set the clock DisplayCannot switch audio Low volumeRemote control doesn’t Sound No soundTroubleshooting guide Maintenance Unit careDisc handling RGB Index
Related manuals
Manual 52 pages 43.42 Kb
Top Page Image Contents