Panasonic DMR-E85H Connecting an amplifier or system component, Connection to a stereo amplifier

Page 9

Connecting a satellite receiver, digital receiver or decoder

≥Decoder here means the device used to decode scrambled broadcasts (Pay TV).

≥Change the “AV2 Input” and “AV2 Connection” settings in the SETUP menu to match the connected equipment (➡page 41).

AV OUT

This unit’s rear panel

Satellite receiver, digital receiver or decoder’s rear panel

21-pin Scart cable

	Y	RF IN
		RF IN
	PB
AV1
	PR
AV2 (DECODER/EXT)	COMPONENT	RF OUT
	VIDEO OUT	RF OUT

(PROGRESSIVE/

INTERLACE)

Viewing video from the decoder on the television while the unit is stopped, or while recording

If you connected the television to the AV1 terminal and the decoder to the AV2 terminal on this unit, press [0]i[ENTER]. (“DVD” appears on the unit’s display.)

Press again to cancel. (“TV” appears on the unit’s display.)

≥If the television is compatible with RGB input, the RGB output signal from the decoder can also be output from the main unit the same way.

Getting started

Connecting an amplifier or system component

∫To enjoy multi-channel surround sound on

DVD-Video

Connect an amplifier with Dolby Digital, DTS and MPEG decoders using an optical digital audio cable and change the settings in “Digital Audio Output” (➡page 40).

≥You cannot use DTS Digital Surround decoders not suited to DVD.

≥Even if using this connection, output will be only 2 channels when playing DVD-Audio.

Amplifier’s rear panel

OPTICAL IN

Optical digital audio cable

Do not bend this cable sharply.

Insert fully, with this side facing up.

R - AUDIO -

OPTICAL

AC IN

DIGITAL AUDIO OUT	R - AUDIO -
(PCM/BITSTREAM)

∫Connection to a stereo amplifier

Amplifier’s rear panel

AUDIO IN

R L

Red White

Audio cable

Red White

R - AUDIO - L	VIDEO S-VIDEO
OPTICAL	OUT

		AV4 IN
DIGITAL AUDIO OUT	R - AUDIO - L	VIDEO S-VIDEO
(PCM/BITSTREAM)

This unit’s rear panel

This unit’s rear panel

Do not place the unit on amplifiers or equipment that may become hot.

The heat can damage the unit.

RQT7664

9

9

Image 9

Contents Example Ejemplo Operating Instructions Instrucciones de funcionamientoStarted Useful features Table of contentsRemote control AccessoriesPlease check and identify the supplied accessories BatteriesControl reference guide Remote controlMain unit Unit’s displayWhen the unit is not to be used for a long time Recommended connection for your televisionDo not connect the unit through a video cassette recorder AV1 terminal Connecting a television with 21-pin Scart terminal and VCRComponent video output ConnectionVideo OUT terminal Component Video OUT terminalConnecting an amplifier or system component To enjoy multi-channel surround sound on DVD-VideoConnection to a stereo amplifier If the clock setting menu appears Preset Download Setup with Q Link functionsEnter ReturnCountry setting menu appears Auto-Setup Setup without Q Link functionsAuto-Setup starts. This takes about 8 minutes Auto-Setup is complete when you see the television pictureSelecting television type and aspect Press 3, 4, 2, 1 to select Setup and press EnterPress Functions To enjoy progressive videoPoint the remote control at the television When the following indicator appears on the unit’s displayTo change the code on the remote control Television operationHDD and discs you can use for recording and play HDD and Disc informationPlay-only discs 12 cm/8 cm Discs that cannot be playedGetting HDD Hard disk drive handling careRecording television programmes Press W X CH to select the channelPress ¥ REC to start recording Recording modes and approximate recording times Playing while you are recordingDirect TV Recording Recording from an external equipment Flexible RecordingUsing Showview number to make timer recordings Timer recordingPress F Timer Press ShowViewPress 3, 4 to select New Timer Manually programming timer recordingsPress PROG/CHECK Press 1 to move through the itemsLinked timer recordings with external equipment EXT Link Check, change or delete a programmePress EXT Link Playing discs BackPlaying Skipping the specified Operations during playTime Time Slip Manual SkipChanging audio Editing operations during playPress Audio Press Erase Press 2, 1 to select Erase and press EnterUsing the tree screen to find a group Using menus to play MP3Press 3, 4, 2, 1 to select a group Press TOP MenuDisc menu-Setting the disc content Using on-screen menus and Status messagesOn-screen menus Press DisplayPress Status Status messagesPlay menu-Change the play sequence Picture menu-Change the picture qualityEditing titles/chapters and playing chapters Editing titles/chaptersPress Direct Navigator Press 3, 4, 2, 1 to select the title Press 3, 4, 2, 1 to select the chapterTitle operations Set up Protection §Press 2, 1 to select Yes and press Enter Press Enter at the start point and endCreating, editing and playing play lists Press 3 to cancelPress 3, 4, 2, 1 to select Play List and press Enter Creating play listsPlay list operations Editing and playing play lists/chaptersMove ChapterShow Enter Name screen Entering textPress 3, 4 To select a Character and press Enter Press SETTransfer Dubbing Transferring dubbing titles or play listsPress Dubbing One Touch Transfer dubbingPress Enter to confirm DubbingTransferring dubbing a finalized DVD-R Press 3, 4 to select Start Dubbing and press EnterTo edit the transferring dubbing list DubbingPress 3, 4, 2, 1 to select an item and press Enter Functions windowPress 3, 4, 2, 1 to select Disc Management and press Enter Press 3, 4 to select the operation and press EnterTop Menu Disc NameDisc Protection Format DiscCommon procedures Changing the unit’s settingsSummary of settings Convenient functionsPicture Tabs Menus Options Underlined items are the factory presetsFunctions TV Aspect AV2 SettingsProgressive TV SystemPress 3, 4 to select Manual and press Enter TuningPress 3, 4, 2 Programme positionTo change the setting all at once PAL!#NTSC Auto-Setup RestartPress 3, 4, 2, 1 to select a country and press Enter TV SystemChild Lock Clock settingsSafety precautions SpecificationsGlossary When programming When ShowviewLink Message Message appears whenSet upPage Frequently asked questionsCover RecordingError messages On the televisionOn the unit’s display Following do not indicate a problem with this unit Troubleshooting guideBreaks ≥Set the clock DisplayCannot switch audio Low volumeRemote control doesn’t Sound No soundTroubleshooting guide Maintenance Unit careDisc handling RGB Index

Related manuals

Manual 52 pages 43.42 Kb