LOREX Technology SC325000 instruction manual Sensor Set, Motion Set

Page 21

Sensor Set

Sensor Set

This submenu allows you to change the settings for a separate sensor device (such as a stand-alone Motion Sensor, or Door/Window Sensor). These sensors are installed on the ALARM

BLOCK (see page 41 for Alarm Block Configuration).

1. SENSOR RECORD DURATION - Sets the length of time for the recording once a sensor input has been detected (i.e. If Motion is detected, the DVR will start recording, and will continue recording for 10 seconds). Navigate to this option using the buttons, and press the button to change the option to one of the following settings: OFF / 10 / 20 / 30 / 40 / 50 and 60 seconds.

2. SENSOR1 - SENSOR4 - Sets the input type for each sensor. Navigate to this option using the buttons, and press the button to change the option to one of the following settings: N/OPEN (Normally Open) or N/CLOSE (Normally Closed).

SENSOR

SENSOR RECORD DUR.[ 10 SEC]

SENSOR1

[ N/OPEN ]

SENSOR2

[ N/OPEN ]

SENSOR3

[ N/OPEN ]

SENSOR4

[ N/OPEN ]

[

]MOVE [

]SELECT [ˆ]EXIT

Motion Set

This submenu allows you to change the settings for cameras with integrated motion sensors.

1. MOTION RECORD DURATION - Sets the length of time for the recording once motion detection has been detected. Navigate to this option using the buttons, and press the button to change the option to one of the following settings: OFF /

10 / 20 / 30 / 40 / 50 and 60 seconds.

2. CHANNEL1 - CHANNEL4 - Sets the Channel to ON/OFF for recording Motion. Navigate to this

option using the buttons, and press the button to change the option.

3. SENSITIVITY - Sets the sensitivity for Motion Detection from 1 (low sensitivity) to 5 (high sensitivity). Navigate to this option using the buttons, and press the button to change the option.

MOTION

MOTION RECORD DUR. [ 10 SEC]

CHANNEL1

[ N]

CHANNEL2

[ Y ]

CHANNEL3

[ N ]

CHANNEL4

[ N ]

SENSITIVITY

[ 3 ]

[

]MOVE [

]SELECT [ˆ]EXIT

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Channel Networkable Digital Video Recorder Page Installation Important SafeguardsService Sentinel Cctv General PrecautionsNetViewer Software DVR FeaturesTable of Contents Table of Contents Remote Control with Batteries Hard Drive not Included Power Supply 12V 5AGetting Started Channel Networkable DVRSC325000 Front Primary Function Buttons Channel Buttons SC325000 Back QUAD/ENTER Change to Remote ControlInstalling the Hard Drive Hard Drive Secure the Hard Drive in the CasingPositioning Reinsert the Cartridge Casing into the DVR UnlockedStarting the DVR Self Test Screens System StartHard Drive Detection Indicates Slave Hard Drive Starting the DVR Quad DisplayMain Menu Control Time / Date Set Date Format Display the Date Format onMenu TIME/DATE Schedule Set Motion Set Sensor SetAlarm 1UU Alarm SetOnly ONE Channel of Audio can be Recorded AT a Time Record SetDefault Load Y/N PasswordAdvanced Menu Set Advanced MenuSystem Information System InformationNetwork Network Recording Functions Recording On screen Messages Menu SettingsTotal Event Master HDD Event no Search Functions Event SearchPlayback Functions Search Functions Time SearchPTZ Pan/Tilt/Zoom Control Minimum System Requirements Operating System NetViewer Installation RequirementsProcessor MemoryNetwork Connectivity DVR Internet RouterNot Included Network Example Router Port ForwardingInternet Router Computer DVRRouter Port Forwarding Ntsc / PAL DVR Specifications Appendix #1DVR BNC Cameras Connecting Cameras to the DVR Appendix #2DVR Slave Monitor Connecting a Slave Monitor Appendix #3Observation System DVR Connecting to an Observation System Appendix #4DVR Sensor Connecting Alarm Device Appendix #5Problem TroubleshootingTroubleshooting It’s all on the web
Top Page Image Contents