TV Operation and Settings, Initial SET UP | Emerson EWL20D6 instruction

- HELPFUL HINTS -

1. PLEASE CHECK TO SEE IF THE ANTENNA/CABLE/SATELLITE IS PROPERLY CONNECTED.

2. DID YOU PERFORM “AUTO PRESET CH” ?

3. PLEASE REFER TO FRONT PAGE OF THE OWNER’S MANUAL OR REAR PANEL FOR SUPPORT LINE INFORMATION.

TV SECTION

TV OPERATION AND SETTINGS

INITIAL SET UP

When you turn on the power for the first time,	TV
the SELECT LANGUAGE screen is displayed.

Select the language for screen display and perform auto programming of the channels.

1 After antenna or cable connection is completed, connect the power cord into a standard AC outlet.

NOTE

•If any digits are displayed in the corner of the screen, press [POWER] without unplugging the power cord.

2 Press [POWER] to turn on the unit.

POWER

WATCHING A TV PROGRAM

1 Press[POWER] to turn on the unit.

POWER

NOTE

• If the TV screen shows snow noise and there is no operation for more than 5 seconds, “HELPFUL HINTS” appears.

Follow the instructions listed on-screen.

•If those settings do not work properly, please call our help line on the front page of this owner's manual.

2 Press [CH. K / L] or the Number buttons to select the desired channel number.

		1	2	3
	OR	4	5	6
CH.	OR	7	8	9

TV OPERATION AND SETTINGS

SECTION

3 Press one of the keys listed below to select the desired language of on-screen menu.

•ENGLISH: [CH. K]

•ESPAÑOL: [CH. L]

•FRANÇAIS: [VOL. X]

4 Confirm the antenna (or cable) connection and press [CH. K].

•The tuner scans and memorizes all active channels in your area.

5 When the scanning is completed, the tuner stops on the lowest memorized channel.

SELECT LANGUAGE

ENGLISH	NEXT:PRESS CHK
ESPAÑOL	DESPUÉS:PRESIONE CHL
FRANÇAIS	APRÈS:PRESSEZ VOLX

– INITIAL SETUP –

PLEASE CONNECT ANTENNA OR CABLE OR SATELLITE TO THIS UNIT.

THEN PRESS CH K,

IN ORDER TO PERFORM “AUTO PRESET CH ”.

CH 15

	+100
0	+10

NOTE

For channel number selection with number buttons:

•To select single-digit channel number, press

[0]first. (e.g. Press [0] [2] for channel 2.)

•To select cable channels which are higher than 99, press [+100/+10] first.

(e.g. Press [+100/+10] [2] [5] for channel 125.)

3 Press [VOL. X / Y] to select the desired vol- ume level.

VOL.

VOLUME 20

C C C C C C C C C C C C C C C C

(Example)

NOTE

•If [MENU] is pressed during channel scanning, the tuner stops scanning and the lowest memo- rized channel is displayed.

•The INITIAL SETUP menu is displayed every time you turn on the unit unless the scanning is completed.

•In case no channel can be received by the channel scan-

ning, “NO TV SIGNALS” is	NO TV SIGNALS
displayed on the screen. Turn
off the unit and check the
antenna connection, then
follow steps 1 to 5 again.

•You can change the setting after completing INITIAL SET UP by LANGUAGE menu or CHANNEL SET UP menu. (Refer to “MENU LANGUAGE” on page 16 or “CHANNEL SET UP” on page 12).

•Press [MUTE] to instantly mute the sound.

Press it again to restore the previous volume level.

NOTE

•If you press [CH. K / L] in the DVD mode, you can change the TV channels. Even if you turn off the unit in the DVD mode, when you turn it on again, it will go into the TV mode.

TO WATCH CABLE OR SATELLITE CHANNEL

If the unit is connected to a cable box or satellite box, press [CH. K / L] to select CH3 or CH4 according to the output channel setting of the device and select desired channel on that device.

TO WATCH EXTERNAL INPUT

When an external equipment is connected to AUDIO/VIDEO input jacks on the right side, press [SELECT] or [CH. K / L] repeatedly until “VIDEO1” or “VIDEO2” appears on the screen.

- 11 -