Grundig CLE91 OS manual Tuning terrestrial television channels DVB-T, English ­17

Page 17

Settings------------------------------------------------------------------------------------------------------------------------------------------

Tuning terrestrial television channels (DVB-T)

1In the »Source Setup« menu, in the »Connec- tion Type« line, select the option »Air« with »<« or »>«.

2Select the line »Scan Type« with »V« or »Λ«.

Usetype:»<« or »>« to set the required scan

»DTV«, scan for digital television channels;

»ATV«, scan for analogue television channels;­

»ATV & DTV«, scan for analogue and

digital­ television channels.

Caution:

7The antenna power supply (5V ) may only be switched on if the antenna is an active

indoor­ antenna with a signal amplifier and it is not already supplied with a voltage via a mains plug (or similar supply). Otherwise you may cause a short circuit and irrepara- bly damage your antenna.

3Select the line »Active Antenna Power« with »V« or »Λ«.

Switch on the antenna power supply for the antenna with »<« or »>« (»On«).

4Start the scan with »« (green).

The »Search Results« menu appears, and the search for TV channels begins.

Depending on the number of television channels received, this can easily take a few minutes.

The scan is complete as soon as the »PRO- GRAM TABLE« appears.

Note:

7You can abort the scan by pressing »MENU«.

5Press »MENU« to end the setting.

Note:

7Before recording HD channels, please check signal quality and Strength, see chapter "Displaying signal information" on page 78. If the level is displayed in green, you can record HD channels without any problems.

Tuning television channels from the cable provider (DVB-C)

1In the »Source Setup« menu, in the »Connec- tion Type« line, select the option »Cable« with »<« or »>«.

2Select the line »Scan Type« with »V« or »Λ«. Use »<« or »>« to set the required scan type:

»DTV«, scan for digital television channels;

»ATV«, scan for analogue television channels;­

»ATV & DTV«, scan for analogue and

digital­ television channels.

3Select the line »Cabel Scan Type« with »V« or »Λ«. Select the preferred option (»Quick« or »Full«) with »<« or »>«.

The search function »Quick« sets up the channels according to the information pro- vided by your cable provider in the trans- mission signal.

If the option »Full« is selected, the entire frequency range will be scanned. The search can take a long time with this op- tion. This option is recommended if your cable provider does not support the scan type »Quick«.

Note:

7You can accelerate the search. To do this, you need information about the frequency and network ID. You are usually able to get this data from your cable operator or find it in forums on the Internet.

4Start the scan with »« (green).

The »Search Results« menu appears, and the search for TV channels begins.

Depending on the number of television channels received, this can easily take a few minutes.

The scan is complete as soon as the »PRO- GRAM TABLE« appears.

Note:

7You can abort the scan by pressing »MENU«.

5Press »MENU« to end the setting.

Note:

7Before recording HD channels, please check signal quality and Strength, see chapter "Displaying signal information" on page 78. If the level is displayed in green, you can record HD channels without any problems.

ENGLISH ­17

Image 17
Contents LCD TV ­2 English Special settings Headphones Hi-fi system/AV receiverLNB settings Settings for motorised antennas DiSEqC Operation with a Common Interface­4 English English ­5 ­6 English Special features of your ­television setGeneral information English ­7 Receiving digital channelsImportant notes on environmental protection Plug the power cord into a wall socket Connecting the antenna and power cordConnection and preparation Antenna­ socket »SATELLITE« on the televi- sion set And/orOpen the battery compartment by removing the lid Inserting batteries into the ­remote controlCompartment­ Close the battery compartment. Note Environmental noteSocket for the mains cable Connections on the television setOptic Out ­10 EnglishEnglish ­11 Controls on the television setVideo ­12 English Remote control Main functionsNavigation in the menus English ­13 Remote control ­ All functions red Selects pages in teletext Selecting language, country and operating mode Initial set-up and tuning ­television channelsVarious settings HelpEasy installation Tuning the television channels from satellite DVB-SAdvanced installation English ­15­16 English English ­17 Tuning terrestrial television channels DVB-TTuning television channels from the cable provider DVB-C ­18 English Changing the program table for the digital channelsSelecting channel lists Change the order of the channels in the program table Deleting channelsSorting channels in the program table Skipping channels­20 English Sorting channels in the favourite listEnter own names for the favourites lists max characters English ­21 Picture settingsSound settings Soundeffects Exiting the settingSRS TruSurround HD EqualizerBasic functions Audio settings Eco modeZoom function Audio languageZapping function Switch back to the channel selection with »«Electronic TV guide Quit the electronic TV guide with »MENU«Changing the picture format ­28 English Important information about the 3D functionPreparing the 3D function English ­29 3D SettingsWatching 3D films Left Right Correction Adjusting 2D → 3D effectsFormats supported by Hdmi ­30 EnglishWired network What is Smart Inter@ctive TVWired network connection Network connectionAutomatic wired network ­ connection Wired network settingsManual wired network connection ­32 EnglishEnglish ­33 Manual connection»DNS« options are active ­34 English Wireless network connectionEnglish ­35 Wireless network settingsAutomatic connection ­36 English Selecting internet applications Smart Inter@ctive TV internet applicationsOpen the menu »SMART inter@ctive TV« with »@« English ­37Navigation in the main menu Smart İnter@ctive browser main menuPlaying and other options in the applications Press »@« to end the applicationEnglish ­39 Select the Digital Media Server»dlna« menu is displayed Start playback VTuner internet radioOther playback functions ­40 EnglishInformation on recording and playing television programmes Possible limitations when using an external data mediumGrundig has no influence on ­ these restrictions English ­41Settings for USB recording Connecting external data mediaSelecting the menu For example, external hard disksTesting the external data medium Switching on automatic previewSafely remove disk Selecting external data mediaRecording programmes ″Pausing time shift ­ programmesOne-touch programme recording ­44 EnglishUsing the electronic TV guide Presetting programmes to be recordedRecording a programme from the channel list English ­45Deleting recording data in the timer menu Editing recording data in the ­ timer menuBy manual data entry ­46 EnglishDeleting programmes in the recording list PlaybackVideo data File formatsAudio data Image data»USB1« socket of the television set Connecting external ­ data mediaDevices­ in EN 55022/EN 55024 is not possible English ­49Selecting the display mode Settings in the USB setup menuSetting the display duration for pictures in a slideshow File browserEnglish ­51 Basic playback functionsDivX VOD Selecting chapters on DivX files Additional playback ­ functionsSelecting titles on DivX files Playing selected titlesSelecting a certain passage for­ playback­ Selecting a track or picture in steps SkipFast forward Repeat functionsAdditional functions TOP text or Flof text modeHbbTV Operation What is HbbTV?Additional functions for video sequences English ­55Language settings Opening the Settings menuTimer settings Setting the date and timeParental control settings Updating software OAD Restoring the television to the default settingsUpdating software Online Convenience functions Changing the PIN codeDigi Link functions on your television English ­61 Switching the device to standbyDevice operation High definition ­HD ready Connection options Connecting external devices With an analogue TV signal HeadphonesConnecting the headphones Changing the headphone volumeSetting the audio format Connecting the hi-fi system/­ AV receiverPlaying the audio signal via the ­ HiFi system Hi-fi system/AV receiverSelecting presets for the PC Connecting a PCSettings for PC mode ­66 EnglishAccess control for CI module and smart card What is a Common Interface?Inserting the CA module English ­67­68 English Cannot­ be changed LNB settingsPress »MENU« to end the setting. English 69­ User mode Settings for motorised antennas DiSEqCReceived­ with »«, »«, »V« or »Λ« and press »OK« to confirm ­70 EnglishEnglish ­71 Expert mode­72 English English ­73 Automatic service updateSearching for digital terrestrial TV channels automatically Switching the television to ­analogue reception Tuning analogue television channels­Setting all analogue television channels Searching for digital terrestrial TV channels manuallyPress »« blue to save the setting To select the preferred setting­Start a automatic scan with »« green oder »« yellow English ­75Selecting a channel list Changing stored analogue channels­Entering channel names 8 digit maximum Skipping television channelsEnglish 77­ Exiting the settings­78 English Displaying signal informationFor digital channels only Open the menu with »MENU« English ­79 Technical dataGrundig New York 40 CLE 9170 SL Environmental note Service information for dealersEnglish ­81 TroubleshootingProvided ISP ­82 EnglishEnglish ­83 Additional Information for units sold in the UK