Sharp 28LF-92H operation manual INSTALL. Installation Menu

• If you know the broadcast band and the channel frequency of the station you want to tune, you do not need to make search; select Frequency, using “ ” or “ ” button in the Frequency Mode Tuning Menu. You can type the first 3 dig- its of the frequency using the digit buttons, and then you can select the decimal part of the frequency by using “ ” or “ ” buttons with 250kHz steps. For example if you want to tune the station at frequency 224.25 MHz; first you can di- rectly type 224. The bar at bottom of the menu will show 224.00 . Then by increasing or decreasing with 0.25 MHz steps using “ ” or “ ” buttons, you can select the 224.25MHz .When you type and select the frequency, the corresponding station will be displayed.

Direct Frequency Access

• As "Frequency Search" is selected, TV will search ac- cording to the channel frequencies.

• With the“ ” or “ ” button, select Search. Search can be made either forward, pressing “ ” button or backwards, pressing “ ” button.

• The search will be done with steps of 0.25MHz. in each step.

• If the tuned station is not the desired one, you can continue searching pressing “ ” or “ ” button again.

• When the desired station is tuned, select STORE using “ ” or “ ” button and store it to the programme number you selected pressing “ ” or “ ” button or press “OK” but- ton.

• Now as you had selected the Frequency Search, the tuning mode of the program is stored as Frequency Search Mode.

select CHANNEL again, and press“ ” or “ ” button to select the channel number, or enter the number with the digit buttons.

5. If the picture is not clear or no colour appears, change the colour system to display the picture normally. Press “ ” or “ ” button to select COLOUR SYSTEM, then press “ ” or “ ” button to choose the correct one.

• In TV mode: PAL / SECAM

• In AV mode: AUTO / PAL / SECAM / NTSC 3.58 / NTSC 4.43

6. If the channel reception is poor, fine-tune the channel. Press “ ” or “ ” to select FINE TUNING, then press “ ” or “ ” button to fine-tune the channel.

7. After the all settings are completed, store the new channel’s setting to the programme number which you se- lected. Press “ ” or “ ” to select STORE, then press

“ ” or “ ” button6&%),1(72(2/285+11(/$$'￿781,1*to&+*￿02'(￿6<67(0store it. 3￿6&+$/$11(/

8. When you select "Frequency Search" , the display of the

Tuning menu 6)&2/25781,1*3will572($(4(1&<2*5&+be$￿02'(￿00(6<67(0as below :￿￿￿￿￿￿3)5(48(1&<$/

INSTALL. (Installation) Menu

You can store a channel manually, or modify the current set- tings of a channel (for example, fine-tuning a channel).

You can also change the colour system.

•Press “M” button to display the main menu.

•Press “” or “” button to select “INSTALL.” item. Then “” or “” button to display,16352*5)(6281',&85($785($the//￿￿￿￿￿￿$0￿￿￿“INSTALL.” menu.

Note:

•If you want to modify the current settings of a channel, se- lect the channel of which you want to modify the setting. Then display the main menu on screen.

•In AV mode, you can change only the “COLOUR SYSTEM” item.

1.PROGRAMME is the first selected item as you enter the

INSTALL. menu. Press the “” or “” button to select the programme number where you want the tuned channel to be stored. (You may also type the programme number us- ing the digit buttons)

Note:

•Do not use the PROGRAMME item when you want to modify the current programme number setting as this may cause other programmes to be changed that are in the ex- isting programme number.

2.Press “” or “” button to select Tuning Mode. By press-

ing “” or “” button , you can select the mode in which you want the search to be made, "Channel Search" mode or "Frequency Search" mode.

•When you select "Channel Search" ("Channel" will be displayed in the menu . ), the display of the

INSTALL.(Installation)6(%),1(352*5$2/285$5&+'11(/￿781,1**$￿02'(￿00(6<67(0Menu will3￿6&+$￿/$11(/be as below :

3.Press “” or “” button to select BAND. Using “” or “” button to select the band in which you want to search a channel.

4.Press “” or “” button to select SEARCH. Press “” or “” button to start searching. (Press “” button to search forward. Press “” to search backwards.)

•If the found channel is not the desired one, press “” or “” button to start searching again.

•To stop searching before a channel is found, press the reverse direction button. For example, when the TV is

searching forward with “” button, press “” button to stop searching.

•If you know the channel number which you want to find, you can find the channel directly. Follow the step 5 to select the correct standard, then press “” or “” to

-14 -

ENG-2862W-3262W-1548UK-2SCART-FAV-SVHS14-AK45-SHARP-TV-1.p65 21.01.2004, 08:28