Connecting external equipment, For Fastext

•Press ““ button to stop the automatic page change.

•Press ““ button again to allow the next page to be dis- played.

To Select a Subcode Page

Subcode pages are subsections of long Teletext pages that can only be displayed on the screen one section at a time.

•Select the required Teletext page.

•Press ““ button.

•Select the required subcode page number by pressing four digit buttons (e.g. 0001).

•If the selected subcode page is not displayed in a short

time, press ““ button. TV programme will be displayed on the screen.

•Teletext page number will be displayed on the upper left corner of the screen when the selected page is found.

•Press ““button to display the selected Teletext page.

Fastext

Teletext mode will be selected according to transmission au- tomatically.

Your TV supports the 7 page Teletext system. When the page number of any of the 7 pages in memory is entered, the system will not search for the requested page; instead it will display the page automatically.

•Press “” button to move the Teletext screen forward one page at a time.

•Press “” button to move the Teletext screen backward one page at a time.

For Fastext

The subject-heading for the information may have a particular colour or can be in a form located in a coloured box.

•Press an appropriate RED, GREEN, YELLOW or BLUE but- ton in order to reach the relevant page quickly.

To exit Teletext

• Press “79” button. The screen will switch to TV mode.

Connecting external equipment

Via the Euro connector

You TV set has two euro connector sockets. If you wish to connect external equipment (e.g. video recorder, decoder, etc.) which have Euro connectors, to your TV, use the EXT.1 (EXT-1) or EXT.2 (EXT-2) terminals.

If an external device is connected via Euro connector sockets the TV will be switched to AV mode automatically.

RGB mode

If a piece of equipment outputs RGB signals use the EXT-1 Euro connector as this is RGB ready.

Via the RCA jacks

If you have an equipment (such as a Camcorder) which has the RCA jacks, connect it to the Front AV (F-AV) terminal with the video and audio cables.

•If the equipment has the mono audio jack, connect it to the AUDIO-L jack.

Via the ANT (aerial) socket

If your equipment does not have an Euroconnector or RCA jacks, connect it to the TV with an aerial cable. For details, see the manual provided with the equipment.

•To store the test signal that comes from the equipment, see “INSTALL. Menu” on page 14 and store it to the pro- gramme number 0. You can watch images from that equip- ment to select the programme number which you stored the test signal.

TV and Video Recoder (VCR)

•Connect the Video Recorder to the ANT (antenna input) socket of the TV with the aerial cable.

•Connect the Video Recorder to the EXT.1 or EXT.2 terminal with the SCART cable, or connect it to the Front AV (F-AV) terminal with the audio and video cables.

NTSC Playback

Connect a NTSC video recorder to a terminal. Then press “(;7” button to select the corresponding AV mode.

NTSC 3.58/4.43 system is detected automatically in AV mode.

Copy Facility

You can output the video and audio signals which inputs from TV or EXT.1 (EXT-1) terminal to the video recorder connected to the EXT.2 (EXT-2) terminal.

•To select the output source, see “Setting External Source Output” on page 13.

To connect to S-VHS input

Connect your camera or camcorder at the front or back side of your TV.

•Connect your equipment to the TV via S-VHS input and au- dio inputs of F-AV inputs by using S-VHS cables.

Connecting Headphones

Use the stereo headphone socket of your TV, to connect headphones.

- 17 -

ENG-2862W-3262W-1548UK-2SCART-FAV-SVHS17-AK45-SHARP-TV-2.p65

21.01.2004, 08:29