Sharp XG-C50X operation manual Setting the Video System

Page 68

Setting the Video System

The video input system mode is preset to “Auto”; however, a clear picture from the con- nected audio-visual equipment may not be received, depending on the video signal differ- ence. In that case, switch the video signal.

Setting the Video

System

Select “Video System” in the “Options (1)” menu on the menu screen.

➝ For operating the menu screen, see pages 42 to 45.

Note

• The video signal can only be set in IN-
PUT 3 or INPUT 4 mode.
• In “Auto”, images are displayed in PAL
even if PAL-N or PAL-M input signals are
received.	PAL	When connected to PAL video equipment.
	SECAM	When connected to SECAM video
		equipment.
	NTSC4.43	When reproducing NTSC signals in
		PAL video equipment.
	NTSC3.58	When connected to NTSC video equipment.

-66

Image 68

Contents XG-C50X Model No. XG-C50X Serial No Introduction Product Disposal Outstanding Features Color Management SystemNoise Reduction New Edge Up-ScalingContents Appendix Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check Wall or Ceiling MountingAvoid locations with high or low temperature Using the projector in other countriesTemperature monitor function Rest your eyes occasionallyTo install Acrobat Reader from the CD-ROM For other operating systems For other languagesFor Windows For MacintoshPart Names Projector Front and Top ViewUsing the Kensington Lock Projector Rear ViewPart Names Remote Control Front ViewRemote Control Top View Using the Remote Control Available Range of the Remote ControlWhen using the remote control Inserting the BatteriesOptional cables AccessoriesSupplied accessories Connections and Setup Connecting the Projector to Other Devices Before ConnectingThis projector can be connected to An audio cable commercially available SeeConnecting the Power Cord Connecting to a Computer Using the RGB Cable Ferrite corePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Connecting to Component Video Equipment CableConnecting to an Amplifier Connecting to an Amplifier or Other Audio ComponentsControlling the Projector by a Computer Connecting to a Monitor Watching Images on Both the Projector and a MonitorButton Using the Wireless Pre- sentation FunctionPress or while using presentation software on your computer Using as a Wired Remote Control Connecting the Remote Control to the ProjectorSetup Using the Adjustment FeetOut Zoom Adjusting the LensFocus ring Zoom knob Setting up the Screen Throw DistanceScreen Size and Projection Distance Normal ModeStretch Mode AN-C12MZ Throw ratio 11.18 to Projecting a Reversed/Inverted Image Projection from behind the screenBasic Operation Basic Procedure Plug the power cord into the wall outletPress on the projector or on the remote control Image ProjectionVolume buttons Press , , or on the remote control to select the Input modePress or on the remote control to adjust the volume Selecting the On-screen Display Language Press to temporarily turn off the soundPress Press \ or to select Lan- guagePress or to select the de- sired language, and then press Press , , \ and to adjust the Keystone correction Correcting Trapezoidal Distortion Keystone CorrectionCorrecting Trapezoidal Distortion Keystone button Enter button Undo button ButtonsUndo button Menu Bar Items Sub menuInput 3 / 4 Mode FAO VAOMenu Bar Main Menu Enter button Buttons Menu button Using the Menu ScreenMenu Selections Adjustments Press \ or to adjust the item selected Press \ or to select the menu you want to adjustPress or to select the item you want to adjust Enter button Buttons Menu button Menu Selections SettingsPress or to select the item you want to set Cursor shifts to the sub menu Selecting the Signal Type Adjusting the PictureAdjusting Image Preferences Progressive Mode Saving Adjustment Settings Adjusting Computer ImagesWhen Auto Sync is OFF Checking the Input Signal Selecting Adjustment SettingsSpecial Mode Settings Auto Sync Adjustment Auto Sync Display FunctionScreen display during Auto Sync Auto Sync buttonEasy to Use Functions Resize button Screen display of the picture display mode Selecting the Picture Display ModeSwitching the Picture Display Using Different Input Signals Video Freeze button Displaying a Still ImageStoring an Image Still Image Format Buttons Enlarge Enlarge/ Reduce buttons Enlarging a Specific Portion of an ImageDisplaying an Enlarged Portion of an Image Adjusting Gamma Correction Gamma Correction FunctionPress to move the inset pic- ture Displaying Dual Pictures Pict in PictDisplaying the Inset Picture Black Screen Function Blacking out the Pro- jected ImageTo return to the original projected image, press again This function can be used to display a black screenDisplaying the Break Timer Displaying and Setting the Break TimerPress to cancel the break timer Buttons Break Timer buttonSelecting the Color Reproduction Mode Selecting the Target ColorSetting the Hue of the Target Color Setting the Brightness of the Target ColorSetting the Chromatic Value of the Target Color Resetting User-Defined Color Settings Overview of All Color SettingsSetting the Audio Output Type Setting on/off the Internal SpeakerSetting the Audio Out- put Type Setting on/off the Inter- nal SpeakerUsing Auto Search Auto Search FunctionSetting On-screen Display Video Digital Noise Reduction DNR SystemReducing Image Noise Turning Off On-screen DisplaySetting the Video System Setting the Video SystemDeleting the Captured Image Saving Projected ImagesCapturing the Image Setting a Background Image Selecting a Startup ImageSelecting a Background Image Selecting a Startup ImageMonitor Out/RS-232C Off Function Selecting the Economy ModeSetting the Power Save Mode Automatic Power Off Function Selecting the Economy ModeDisplaying the Remaining Lamp Life Percentage Checking the Remaining Lamp Life PercentageSetting the Projection Mode Setting up the KeylockReversing/Inverting Projected Images Locking the Operation Buttons on the ProjectorSelecting the Transmis- sion Speed RS-232C Canceling the Keylock SettingSelecting the Transmission Speed RS-232C Setting up a Password Entering the PasswordEnter the new 4-digit password again in Reconfirm Changing the PasswordIf You Forget Your Password Setting the Anti-Theft Entering the KeycodeChanging the Keycode Enter the same 4-digit keycode in ReconfirmInitializing the Settings Returning to Default SettingsDisplaying the Adjustment Settings Overview of All Menu SettingsAppendix Maintenance Cleaning the projectorCleaning the lens Cleaning the exhaust and intake ventsCleaning and replacing the bottom air filter Turn off the power and discon- nect the power cordReplacing the Air Filter Remove the bottom filter coverReplace the filter cover Clean the air filterReplace the air filter About the lamp replacement indicator Maintenance IndicatorsAbout the temperature warning indicator Maintenance Indicators Replacing the Lamp Regarding the LampLamp Removing and Install- ing the Lamp Unit Press on the projector to turn off the powerDisconnect the power cord Change the air filterResetting the Lamp Timer Connecting Pin Assignments RGB Input Component InputRS-232C Specifications and Command Settings CommandsPC control Communication conditionsRS-232C Specifications and Command Settings Options Control Contents Wired Remote Control Terminal Specifications Specifications of wired remote control inputSharp remote control signal format Function and transmisson codesComputer Compatibility Chart ComputerTroubleshooting Troubleshooting For Sharp Assistance Specifications Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAMDimensions Units inches mmGlossary Advanced intelligent compressionIndex 100Stretch 101Sharp Corporation