Sharp XG-C50X operation manual Resetting the Lamp Timer

Page 89

5Remove the lamp unit.

•Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow.

6Insert the new lamp unit.

•Press the lamp unit firmly into the lamp unit compartment. Fasten the secur- ing screws.

7Attach the lamp unit cover.

•Insert the tab of the lamp unit cover into the opening, and press the cover until it clicks in place.

Info

•If the lamp unit and lamp cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

1Connect the power cord.

•Plug the power cord into the AC socket of the projector.

2 Reset the lamp timer.

•While pressing simultaneously ,

ON

and on the projector, press on the projector.

•“LAMP 100%” is displayed, indicating that the lamp timer is reset.

Info

•Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

Securing screw

User service screw

AC socket

INPUT button ENTER button

Power (ON) button

UNDO buttom

Appendix

-87

Image 89

Contents XG-C50X Model No. XG-C50X Serial No Introduction Product Disposal Color Management System Outstanding FeaturesNoise Reduction New Edge Up-ScalingContents Appendix Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check Wall or Ceiling MountingUsing the projector in other countries Avoid locations with high or low temperatureTemperature monitor function Rest your eyes occasionallyFor other operating systems For other languages To install Acrobat Reader from the CD-ROMFor Windows For MacintoshProjector Front and Top View Part NamesProjector Rear View Using the Kensington LockPart Names Remote Control Front ViewRemote Control Top View Available Range of the Remote Control Using the Remote ControlWhen using the remote control Inserting the BatteriesOptional cables AccessoriesSupplied accessories Connections and Setup Before Connecting Connecting the Projector to Other DevicesThis projector can be connected to An audio cable commercially available SeeConnecting the Power Cord Ferrite core Connecting to a Computer Using the RGB CablePlug and Play function when connecting to a 15-pin terminal Connecting to Video Equipment Cable Connecting to Component Video EquipmentConnecting to an Amplifier or Other Audio Components Connecting to an AmplifierControlling the Projector by a Computer Watching Images on Both the Projector and a Monitor Connecting to a MonitorButton Using the Wireless Pre- sentation FunctionPress or while using presentation software on your computer Connecting the Remote Control to the Projector Using as a Wired Remote ControlUsing the Adjustment Feet SetupOut Zoom Adjusting the LensFocus ring Zoom knob Throw Distance Setting up the ScreenScreen Size and Projection Distance Normal ModeStretch Mode AN-C12MZ Throw ratio 11.18 to Projection from behind the screen Projecting a Reversed/Inverted ImageBasic Operation Plug the power cord into the wall outlet Basic ProcedurePress on the projector or on the remote control Image ProjectionVolume buttons Press , , or on the remote control to select the Input modePress or on the remote control to adjust the volume Press to temporarily turn off the sound Selecting the On-screen Display LanguagePress Press \ or to select Lan- guagePress or to select the de- sired language, and then press Correcting Trapezoidal Distortion Keystone Correction Press , , \ and to adjust the Keystone correctionCorrecting Trapezoidal Distortion Keystone button Enter button Undo button ButtonsUndo button Sub menu Menu Bar ItemsFAO VAO Input 3 / 4 ModeMenu Bar Main Menu Enter button Buttons Menu button Using the Menu ScreenMenu Selections Adjustments Press \ or to adjust the item selected Press \ or to select the menu you want to adjustPress or to select the item you want to adjust Enter button Buttons Menu button Menu Selections SettingsPress or to select the item you want to set Cursor shifts to the sub menu Selecting the Signal Type Adjusting the PictureAdjusting Image Preferences Progressive Mode Saving Adjustment Settings Adjusting Computer ImagesWhen Auto Sync is OFF Checking the Input Signal Selecting Adjustment SettingsSpecial Mode Settings Auto Sync Display Function Auto Sync AdjustmentScreen display during Auto Sync Auto Sync buttonEasy to Use Functions Resize button Screen display of the picture display mode Selecting the Picture Display ModeSwitching the Picture Display Using Different Input Signals Video Freeze button Displaying a Still ImageStoring an Image Still Image Format Buttons Enlarge Enlarge/ Reduce buttons Enlarging a Specific Portion of an ImageDisplaying an Enlarged Portion of an Image Gamma Correction Function Adjusting Gamma CorrectionPress to move the inset pic- ture Displaying Dual Pictures Pict in PictDisplaying the Inset Picture Blacking out the Pro- jected Image Black Screen FunctionTo return to the original projected image, press again This function can be used to display a black screenDisplaying and Setting the Break Timer Displaying the Break TimerPress to cancel the break timer Buttons Break Timer buttonSelecting the Target Color Selecting the Color Reproduction ModeSetting the Hue of the Target Color Setting the Brightness of the Target ColorSetting the Chromatic Value of the Target Color Overview of All Color Settings Resetting User-Defined Color SettingsSetting on/off the Internal Speaker Setting the Audio Output TypeSetting the Audio Out- put Type Setting on/off the Inter- nal SpeakerAuto Search Function Using Auto SearchVideo Digital Noise Reduction DNR System Setting On-screen DisplayReducing Image Noise Turning Off On-screen DisplaySetting the Video System Setting the Video SystemDeleting the Captured Image Saving Projected ImagesCapturing the Image Selecting a Startup Image Setting a Background ImageSelecting a Background Image Selecting a Startup ImageMonitor Out/RS-232C Off Function Selecting the Economy ModeSetting the Power Save Mode Selecting the Economy Mode Automatic Power Off FunctionDisplaying the Remaining Lamp Life Percentage Checking the Remaining Lamp Life PercentageSetting up the Keylock Setting the Projection ModeReversing/Inverting Projected Images Locking the Operation Buttons on the ProjectorSelecting the Transmis- sion Speed RS-232C Canceling the Keylock SettingSelecting the Transmission Speed RS-232C Entering the Password Setting up a PasswordEnter the new 4-digit password again in Reconfirm Changing the PasswordIf You Forget Your Password Entering the Keycode Setting the Anti-TheftEnter the same 4-digit keycode in Reconfirm Changing the KeycodeReturning to Default Settings Initializing the SettingsOverview of All Menu Settings Displaying the Adjustment SettingsAppendix Cleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake ventsTurn off the power and discon- nect the power cord Cleaning and replacing the bottom air filterReplacing the Air Filter Remove the bottom filter coverReplace the filter cover Clean the air filterReplace the air filter About the lamp replacement indicator Maintenance IndicatorsAbout the temperature warning indicator Maintenance Indicators Replacing the Lamp Regarding the LampLamp Press on the projector to turn off the power Removing and Install- ing the Lamp UnitDisconnect the power cord Change the air filterResetting the Lamp Timer RGB Input Component Input Connecting Pin AssignmentsCommands RS-232C Specifications and Command SettingsPC control Communication conditionsRS-232C Specifications and Command Settings Options Control Contents Specifications of wired remote control input Wired Remote Control Terminal SpecificationsSharp remote control signal format Function and transmisson codesComputer Computer Compatibility ChartTroubleshooting Troubleshooting For Sharp Assistance Ntsc 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM SpecificationsUnits inches mm DimensionsAdvanced intelligent compression Glossary100 Index101 StretchSharp Corporation