Sharp LC C4067U CH Setup, PC Setup, Input Signal for Analog PC Input Mode Only, Input Skip

Page 20
CH Setup

On-Screen Display Menu

CH Setup

If initial setup does not memorize all the channels in your region, follow the instructions below to manually memorize the channels.

Air/Cable: Make sure what kind of connection is made with your TV when selecting "Air" or "Cable".

CH Search: Channel auto search makes the TV look for all channels viewable in the set area.

CH Memory: You can select the channels to skip in each ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and DIGITAL (Cable).

On: Skips channels. (Channel selection disabled using CH r/s.)

Off: Does not skip channels. (Channel selection enabled using CHr/s.)

PC Setup

Input Signal (for Analog PC Input Mode Only)

Some input signals may have to be registered manually to display properly. The pair of input signals (resolutions) in the list below is not distinguishable when received.

In such a case, you have to set the correct signal manually. After setting once, it will display when the same signal (resolution) is input again.

1024 x 768

1360 x 768

Antenna Setup Digital: In order to receive digital air broadcasts, you need a digital broadcast antenna. You can confi rm the antenna confi guration through the "Antenna Setup Digital" screen. If necessary, adjust the direction of the antenna to obtain the maximum signal strength.

Signal Strength: The signal strength of DIGITAL channel is displayed. The signal information is based on the current channel.

Channel Strength: Input the 2-digit channel number to check the signal strength of the selected channel. Make sure the signal is strong enough for each channel.

•This function is available for DIGITAL (Air) only.

•See "Initial Setup" on page 12 for setting each item.

•If no channel is found, confi rm the type of connection made with your TV and try channel search again.

•You can only select the "Input Signal" on the Setup menu when receiving one of the 2 input signals listed above.

Auto Sync. (for Analog PC Input Mode Only)

For automatically adjusting the PC image.

Yes: Auto Sync. starts.

No: This function does not work.

•When Auto Sync. is successful, "Completed" displays. If not, Auto Sync. failed.

•Auto Sync. may fail even if "Completed" displays.

•Auto Sync. may fail if the computer image has low resolution, has unclear (black) edges, or is moved while executing Auto Sync.

•Be sure to connect the PC to the TV and switch it on before starting Auto Sync.

Input Skip

This setting allows you to skip the HDMI or PC-IN Input ("Input 4 (PC)", "Input 5 (HDMI)", "Input 6 (HDMI)", "Input 7 (HDMI)" and "Input 8 (HDMI)") on the Input Selection operation.

Yes: Skips the input.

No: Does not skip input.

Input Label

Lets you set the input terminal displayed when using the INPUT SOURCE menu or channel display. Press a/b/c/d to select the new name for the input mode.

• You cannot change labels if the INPUT SOURCE is TV.

Position

For adjusting a picture's horizontal and vertical position.

H-Pos.:Centers the image by moving it to the left or right.

V-Pos.:Centers the image by moving it up or down.

•For resetting adjustments to the factory preset values, press a/b to select "Reset", and then press ENTER.

•When connecting a PC to the HDMI terminal, the image position will be automatically adjusted. It cannot be manually adjusted.

•Adjustments are stored separately according to input source.

•When a DTV channel is selected, the horizontal position cannot be adjusted.

•The horizontal and/or vertical position may not be able to

be adjusted or it may be adjusted only to a certain degree. 20

Fine Sync.

Ordinarily you can easily adjust the picture as necessary to change image position using Auto Sync. In some cases, however, manual adjustment is needed to optimize the image.

H-Pos.:Centers the image by moving it to the left or right.

V-Pos.:Centers the image by moving it up or down.

Clock: Adjust when the image fl ickers with vertical stripes.

Phase: Adjust when characters have low contrast or when the image fl ickers.

•For resetting all Fine Sync. adjustment items to the factory preset values, press a/b to select "Reset", and then press

ENTER.

•It is not necessary to adjust the "Clock" or "Phase" when a digital signal is being input, so it cannot be selected.

•The default cursor position may not be in the center, because the screen position variable ranges may be asymmetrical.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Supplied Accessories Make sure the following accessories are provided with the productLC-C4067U LIQUID CRYSTAL TELEVISIONTINS-E192WJZZ IMPORTANT INFORMATIONModel No Serial No Sharp at 1-800-BE-SHARP For U.S.A. onlyDECLARATION OF CONFORMITY INFORMATIONDEAR SHARP CUSTOMER IMPORTANT SAFETY INSTRUCTIONSAdditional Safety Information Precautions when transporting the TV THE ISSUE TUNE INTO SAFETYTHIS MANUFACTURER CARES WALL MOUNTING IF YOU DECIDE TO WALL MOUNT YOUR FLATSetting the TV on the Wall Using an optional bracket to mount the TVAbout setting the TV angle QUICK REFERENCEQUICK INSTALLATION TIPS Using the Remote Control Unit4 How to turn on the television for the fi rst time A Press POWER on the televisionInstalling Batteries in the Remote Control Unit NOTICE F-type connector should be finger-tightened onlyConnecting Antenna Cable PreparationPOWER Part NamesTV Front TV Rear/SideConnecting to External Equipment Connecting a PCTurning On/Off the Power Initial SetupWatching TV ENTERPOWER You can select 4 preset favorite channels in 4 different categoriesChanging Volume Sleep TimerAllows you to gain quick access to PC mode. Press PC When the input source is TV, INPUT 1, 2 or 3 terminalsWhen the input source is INPUT 4, 5, 6, 7 or 8 terminals You can enjoy Hi-Fi stereo sound or SAP broadcasts where availableINPUT 1 Press INPUT2 Press INPUT again or press a/b to select the input source 1 Press CCInput signal VIEW MODEYou can select the screen size 1 Press VIEW MODEUsing the remote control Use the following buttons on the remote control to operate the menuUsing the control panel of the main unit MENU MENU on the remote control INPUT ENTER on the remote controlOPC Setting Advanced Picture SettingPicture Menu On-Screen Display MenuPower Control Menu Setup MenuNo Signal Off Power control setting allows you to save energyCH Setup PC SetupInput Signal for Analog PC Input Mode Only Auto Sync. for Analog PC Input Mode OnlyParental CTRL Parental Control Setting Three conditions must be met to enable the V-Chip see pages 22 and2. V-Chip/V-Chip DTV Only settings have been made Audio SetupV-Chip MPAA Voluntary movie rating systemTV Parental Guidelines Suggested age TV-Y All children TV-Y7 Directed to older childrenHow to temporarily release the V-CHIP BLOCK Canadian English RatingsCanadian French Ratings Reactivating the temporarily released V-CHIP BLOCKDigital Caption Setup Select the CH display when changing channels for digital broadcastingOption Menu Audio OnlyFavorite CH Favorite Channel Setting Software Update3 Press a/b to select “Software Update”, and then press ENTER 4 Input the 4-digit secret number by using6 During the data checking, “Checking” blinks 7 Press ENTER to start updating9 After the screen shown below is displayed, press 10 Remove the USB memory deviceTroubleshooting Troubleshooting-Digital BroadcastingThe error message about reception of broadcast ProblemCommand format Communication procedureCommand table RS-232C Port SpecificationsOptional Accessory SpecificationsModel LC-C4067U Part namePC Compatibility Chart ResolutionCLEARING THE SECRET NUMBER The secret number isCalling for Service LIMITED WARRANTYCONSUMER LIMITED WARRANTY Warranty Period for this Product Additional Exclusions fromDimensional Drawings 15 3 / 4Unit inch mm Unidad pulgada mm 4 37/64
Top Page Image Contents