Sharp LC C4067U Preparation, Antennas, Installing Batteries in the Remote Control Unit

Page 9
Preparation

Preparation

Antennas

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the antenna terminal at the rear of the TV set.

1.A 75-ohm system is generally a round cable with F-type connector that can easily be attached to a terminal without tools (Commercially available).

2.A 300-ohm system is a fl at “twin-lead” cable that can be attached to a 75-ohm terminal through a 300/75-ohm adapter (Commercially available).

Antennas F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (fl at)

NOTICE F-type connector should be finger-tightened only.

When connecting the RF cable to the TV set, do not tighten F-type connector with tools.

If tools are used, it may cause damage to your TV set. (The breaking of internal circuit, etc.)

Connecting Antenna Cable

F-type connector

75-ohm coaxial cable

• Connect the antenna cable to the TV using one of the methods in the illustration as shown (1, 2, 3 or 4).

1Cable without a CATV converter

2VHF/UHF antenna

3Combination VHF/ UHF antenna

4Separate VHF/UHF antenna

 

 

 

Home Antenna

 

Cable TV lead-In

 

terminal (75-ohm)

 

 

 

 

 

 

 

Coaxial cable

 

 

 

(commercially available)

 

 

 

Home Antenna

 

75-ohm coaxial cable (round)

terminal (75-ohm)

 

 

 

 

 

 

Coaxial cable

 

 

 

(commercially available)

 

75-ohm coaxial cable (round)

 

 

 

 

 

or

 

 

 

 

300/75-ohm adapter

 

300-ohm twin-lead cable (flat)

(commercially available)

 

 

 

 

UHF

300-ohm

 

 

VHF

ANTENNA

 

 

twin-lead cable

 

 

 

 

 

ANTENNA

 

IN

OUT

 

 

 

 

 

 

Combiner

 

300-ohm twin-lead cable

(commercially available)

or

75-ohm coaxial cable

To TV antenna

terminal

 

 

Installing Batteries in the Remote Control Unit

If the remote control fails to operate TV functions, replace the batteries in the remote control unit.

1 Open the battery cover.

2 Insert two “AA” size batteries

3 Close the battery cover.

 

(supplied with the product).

 

•Place the batteries with their terminals corresponding to the (e) and (f) indications in the battery compartment.

CAUTION

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

•Do not mix batteries of different types. Different types of batteries have different characteristics.

•Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries.

•Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a rash. If you fi nd any chemical leakage, wipe thoroughly with a cloth.

•The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

•If you will not be using the remote control unit for an extended period of time, remove batteries from it.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Make sure the following accessories are provided with the product Supplied AccessoriesLC-C4067U LIQUID CRYSTAL TELEVISIONIMPORTANT INFORMATION Model No Serial NoTINS-E192WJZZ For U.S.A. only Sharp at 1-800-BE-SHARPDECLARATION OF CONFORMITY INFORMATIONIMPORTANT SAFETY INSTRUCTIONS Additional Safety InformationDEAR SHARP CUSTOMER Precautions when transporting the TV TUNE INTO SAFETY THE ISSUETHIS MANUFACTURER CARES WALL MOUNTING IF YOU DECIDE TO WALL MOUNT YOUR FLATUsing an optional bracket to mount the TV Setting the TV on the WallAbout setting the TV angle QUICK REFERENCEUsing the Remote Control Unit QUICK INSTALLATION TIPS4 How to turn on the television for the fi rst time A Press POWER on the televisionNOTICE F-type connector should be finger-tightened only Installing Batteries in the Remote Control UnitConnecting Antenna Cable PreparationPart Names POWERTV Front TV Rear/SideConnecting a PC Connecting to External EquipmentInitial Setup Turning On/Off the PowerWatching TV ENTERYou can select 4 preset favorite channels in 4 different categories POWERChanging Volume Sleep TimerWhen the input source is TV, INPUT 1, 2 or 3 terminals Allows you to gain quick access to PC mode. Press PCWhen the input source is INPUT 4, 5, 6, 7 or 8 terminals You can enjoy Hi-Fi stereo sound or SAP broadcasts where available1 Press INPUT INPUT2 Press INPUT again or press a/b to select the input source 1 Press CCVIEW MODE Input signalYou can select the screen size 1 Press VIEW MODEUse the following buttons on the remote control to operate the menu Using the remote controlUsing the control panel of the main unit MENU MENU on the remote control INPUT ENTER on the remote controlAdvanced Picture Setting OPC SettingPicture Menu On-Screen Display MenuSetup Menu Power Control MenuNo Signal Off Power control setting allows you to save energyPC Setup CH SetupInput Signal for Analog PC Input Mode Only Auto Sync. for Analog PC Input Mode OnlyThree conditions must be met to enable the V-Chip see pages 22 and Parental CTRL Parental Control Setting2. V-Chip/V-Chip DTV Only settings have been made Audio SetupMPAA Voluntary movie rating system V-ChipTV Parental Guidelines Suggested age TV-Y All children TV-Y7 Directed to older childrenCanadian English Ratings How to temporarily release the V-CHIP BLOCKCanadian French Ratings Reactivating the temporarily released V-CHIP BLOCKSelect the CH display when changing channels for digital broadcasting Digital Caption SetupOption Menu Audio OnlySoftware Update Favorite CH Favorite Channel Setting3 Press a/b to select “Software Update”, and then press ENTER 4 Input the 4-digit secret number by using7 Press ENTER to start updating 6 During the data checking, “Checking” blinks9 After the screen shown below is displayed, press 10 Remove the USB memory deviceTroubleshooting-Digital Broadcasting TroubleshootingThe error message about reception of broadcast ProblemCommunication procedure Command formatCommand table RS-232C Port SpecificationsSpecifications Optional AccessoryModel LC-C4067U Part nameResolution PC Compatibility ChartCLEARING THE SECRET NUMBER The secret number isLIMITED WARRANTY Calling for ServiceCONSUMER LIMITED WARRANTY Warranty Period for this Product Additional Exclusions from15 3 / 4 Dimensional DrawingsUnit inch mm Unidad pulgada mm 4 37/64
Top Page Image Contents