Sharp LC C4067U During the data checking, “Checking” blinks, Press ENTER to start updating, Enter

Page 26
6During the data checking, “Checking” blinks.

On-Screen Display Menu

6During the data checking, “Checking” blinks.

Now checking the data in the USB memory device.

Checking

•The current version of the TV software and the version of the update fi le on the USB memory device are displayed. To update the TV software with the update fi le, select “Yes”, and then press ENTER.

Example

Software update file is detected in the USB memory device.

Start update?

Current Version:

UXXXXXX1

Update Version:

UXXXXXX2

 

 

 

Yes

 

No

 

 

 

•If the USB memory device is not properly installed or the correct update fi le cannot be found on the USB memory device, an error message is displayed.

•Check the fi le on the USB memory device, and then reinsert the USB memory device correctly.

Software update file is not detected

in the USB memory device.

Confirm that you have transferred the file

to the USB memory device and retry software update. Confirm that you have inserted the USB memory device into the SERVICE port near the INPUT3.

OK

There is more than one software file in the USB memory device.

Confirm that only the software update file is in the USB memory device.

OK

7Press ENTER to start updating.

•The screen becomes dark for a while until the update screen can be displayed. Please wait for the update screen to appear. Do not unplug the AC cord.

The picture will temporarily go dark until the Software Update display appears.

Wait several minutes and do not unplug the AC cord.

OK

Example

Now updating

7Press ENTER to start updating.Do not unplug AC cord.

Update Version

UXXXXXX2

30%

CAUTION

•Do not remove the USB memory device or unplug the AC cord while the software is being updated.

8When the software is successfully updated, a screen is displayed indicating that the update process is completed.

After this screen is displayed, the TV automatically turns off and then turns on again.

Example

Software update is complete.

Update Version

UXXXXXX2

•If the update has failed, check the fi le in the USB memory device and try Software Update again.

Failed to complete update. Retry Software Update.

If system Update fails again, contact the customer service center.

9After the screen shown below is displayed, press

ENTER.

System software was successfully updated.

Remove the USB memory device.

OK

10 Remove the USB memory device.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents LC-C4067U Supplied AccessoriesMake sure the following accessories are provided with the product LIQUID CRYSTAL TELEVISIONTINS-E192WJZZ IMPORTANT INFORMATIONModel No Serial No DECLARATION OF CONFORMITY Sharp at 1-800-BE-SHARPFor U.S.A. only INFORMATIONDEAR SHARP CUSTOMER IMPORTANT SAFETY INSTRUCTIONSAdditional Safety Information Precautions when transporting the TV THIS MANUFACTURER CARES THE ISSUETUNE INTO SAFETY WALL MOUNTING IF YOU DECIDE TO WALL MOUNT YOUR FLATAbout setting the TV angle Setting the TV on the WallUsing an optional bracket to mount the TV QUICK REFERENCE4 How to turn on the television for the fi rst time QUICK INSTALLATION TIPSUsing the Remote Control Unit A Press POWER on the televisionConnecting Antenna Cable Installing Batteries in the Remote Control UnitNOTICE F-type connector should be finger-tightened only PreparationTV Front POWERPart Names TV Rear/SideConnecting to External Equipment Connecting a PCWatching TV Turning On/Off the PowerInitial Setup ENTERChanging Volume POWERYou can select 4 preset favorite channels in 4 different categories Sleep TimerWhen the input source is INPUT 4, 5, 6, 7 or 8 terminals Allows you to gain quick access to PC mode. Press PCWhen the input source is TV, INPUT 1, 2 or 3 terminals You can enjoy Hi-Fi stereo sound or SAP broadcasts where available2 Press INPUT again or press a/b to select the input source INPUT1 Press INPUT 1 Press CCYou can select the screen size Input signalVIEW MODE 1 Press VIEW MODEUsing the control panel of the main unit Using the remote controlUse the following buttons on the remote control to operate the menu MENU MENU on the remote control INPUT ENTER on the remote controlPicture Menu OPC SettingAdvanced Picture Setting On-Screen Display MenuNo Signal Off Power Control MenuSetup Menu Power control setting allows you to save energyInput Signal for Analog PC Input Mode Only CH SetupPC Setup Auto Sync. for Analog PC Input Mode Only2. V-Chip/V-Chip DTV Only settings have been made Parental CTRL Parental Control SettingThree conditions must be met to enable the V-Chip see pages 22 and Audio SetupTV Parental Guidelines V-ChipMPAA Voluntary movie rating system Suggested age TV-Y All children TV-Y7 Directed to older childrenCanadian French Ratings How to temporarily release the V-CHIP BLOCKCanadian English Ratings Reactivating the temporarily released V-CHIP BLOCKOption Menu Digital Caption SetupSelect the CH display when changing channels for digital broadcasting Audio Only3 Press a/b to select “Software Update”, and then press ENTER Favorite CH Favorite Channel SettingSoftware Update 4 Input the 4-digit secret number by using9 After the screen shown below is displayed, press 6 During the data checking, “Checking” blinks7 Press ENTER to start updating 10 Remove the USB memory deviceThe error message about reception of broadcast TroubleshootingTroubleshooting-Digital Broadcasting ProblemCommand table Command formatCommunication procedure RS-232C Port SpecificationsModel LC-C4067U Optional AccessorySpecifications Part nameCLEARING THE SECRET NUMBER PC Compatibility ChartResolution The secret number isCONSUMER LIMITED WARRANTY Calling for ServiceLIMITED WARRANTY Warranty Period for this Product Additional Exclusions fromUnit inch mm Unidad pulgada mm Dimensional Drawings15 3 / 4 4 37/64
Top Page Image Contents