Sharp LC C4067U Dimensional Drawings, 15 3 / 4, Unit inch mm Unidad pulgada mm, 4 37/64, 20 3/4

Page 32

Dimensional Drawings

/16 (687)		11/32 (618)
27 1		24

47/64		(69)
2
8 23/64		(212)
8 23/64		(212)
/4 (400)
3

387/8 (987)

34 61/64 (887.8)

19 45/64 (500.35)	/64 (397)
	15 41

20 3/4 (527)

15 3/4 (400)

Unit: inch (mm)

Unidad: pulgada (mm)

4 37/64

4 7/32

(116)(107)

1213/16

(325)

Image 32

Contents Supplied Accessories Make sure the following accessories are provided with the productLC-C4067U LIQUID CRYSTAL TELEVISIONTINS-E192WJZZ IMPORTANT INFORMATIONModel No Serial No Sharp at 1-800-BE-SHARP For U.S.A. onlyDECLARATION OF CONFORMITY INFORMATIONDEAR SHARP CUSTOMER IMPORTANT SAFETY INSTRUCTIONSAdditional Safety Information Precautions when transporting the TV THE ISSUE TUNE INTO SAFETYTHIS MANUFACTURER CARES WALL MOUNTING IF YOU DECIDE TO WALL MOUNT YOUR FLATSetting the TV on the Wall Using an optional bracket to mount the TVAbout setting the TV angle QUICK REFERENCEQUICK INSTALLATION TIPS Using the Remote Control Unit4 How to turn on the television for the ﬁ rst time A Press POWER on the televisionInstalling Batteries in the Remote Control Unit NOTICE F-type connector should be ﬁnger-tightened onlyConnecting Antenna Cable PreparationPOWER Part NamesTV Front TV Rear/SideConnecting to External Equipment Connecting a PCTurning On/Off the Power Initial SetupWatching TV ENTERPOWER You can select 4 preset favorite channels in 4 different categoriesChanging Volume Sleep TimerAllows you to gain quick access to PC mode. Press PC When the input source is TV, INPUT 1, 2 or 3 terminalsWhen the input source is INPUT 4, 5, 6, 7 or 8 terminals You can enjoy Hi-Fi stereo sound or SAP broadcasts where availableINPUT 1 Press INPUT2 Press INPUT again or press a/b to select the input source 1 Press CCInput signal VIEW MODEYou can select the screen size 1 Press VIEW MODEUsing the remote control Use the following buttons on the remote control to operate the menuUsing the control panel of the main unit MENU MENU on the remote control INPUT ENTER on the remote controlOPC Setting Advanced Picture SettingPicture Menu On-Screen Display MenuPower Control Menu Setup MenuNo Signal Off Power control setting allows you to save energyCH Setup PC SetupInput Signal for Analog PC Input Mode Only Auto Sync. for Analog PC Input Mode OnlyParental CTRL Parental Control Setting Three conditions must be met to enable the V-Chip see pages 22 and2. V-Chip/V-Chip DTV Only settings have been made Audio SetupV-Chip MPAA Voluntary movie rating systemTV Parental Guidelines Suggested age TV-Y All children TV-Y7 Directed to older childrenHow to temporarily release the V-CHIP BLOCK Canadian English RatingsCanadian French Ratings Reactivating the temporarily released V-CHIP BLOCKDigital Caption Setup Select the CH display when changing channels for digital broadcastingOption Menu Audio OnlyFavorite CH Favorite Channel Setting Software Update3 Press a/b to select “Software Update”, and then press ENTER 4 Input the 4-digit secret number by using6 During the data checking, “Checking” blinks 7 Press ENTER to start updating9 After the screen shown below is displayed, press 10 Remove the USB memory deviceTroubleshooting Troubleshooting-Digital BroadcastingThe error message about reception of broadcast ProblemCommand format Communication procedureCommand table RS-232C Port SpeciﬁcationsOptional Accessory SpeciﬁcationsModel LC-C4067U Part namePC Compatibility Chart ResolutionCLEARING THE SECRET NUMBER The secret number isCalling for Service LIMITED WARRANTYCONSUMER LIMITED WARRANTY Warranty Period for this Product Additional Exclusions fromDimensional Drawings 15 3 / 4Unit inch mm Unidad pulgada mm 4 37/64