Sharp LC-46LE700S LC-52LE700E LC-52LE700S, LC-40LE700S, LC-40LE700E RS-232C port specifications

Page 41

Connecting a PC

RS-232C port specifications

PC control of the TV

When a programme is set, the TV can be controlled from the PC using the RS-232C terminal. The input signal (PC/video) can be selected, the volume can be adjusted and various other adjustments and settings can be made, enabling automatic programmed playing.

Use an RS-232C serial control cable (cross type) (commercially available) for the connections.

NOTE

This operation system should be used by a person who is accustomed to using PCs.

RS-232C serial control cable (cross type)

Communication conditions

Set the RS-232C communications settings on the PC to match the TV’s communications conditions. The TV’s communications settings are as follows:

Baud rate

9,600 bps

 

 

Data length

8 bits

 

 

Parity bit

None

 

 

Stop bit

1 bit

 

 

Flow control

None

Communication procedure

Send the control commands from the PC via the RS- 232C connector.

The TV operates according to the received command and sends a response message to the PC.

Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the next command.

Make sure to send “A” with the carriage return and confirm that “ERR” returns before operating.

Command format

Eight ASCII codes +CR

C1 C2 C3 C4 P1 P2 P3 P4

Command four digits: Command. The text of four characters.

Parameter four digits: Parameter 0_9, blank, ?, minus

Return code (0DH): ?

Parameter

Input the parameter values, aligning left, and fill with blank(s) for the remainder (be sure that four values are input for the parameter).

When the input parameter is not within an adjustable range, “ERR” returns (refer to “Response code format”).

0

0

0

0

9

 

 

 

 

 

 

 

 

1

0

0

 

 

 

 

 

 

 

 

 

0

0

5

5

 

 

 

 

When “?” is input for some commands, the present setting value responds.

? ? ? ?

Response code format

Normal response

OK

Return code (0DH)

Problem response (communication error or incorrect command)

E R R

Return code (0DH)

39

Image 41
Contents Italiano Français Deutsch English Blue Neutral Brown Live Special Note for Users in the U.KDear Sharp customer TrademarksIntroduction Important safety precautionsPrecautions when transporting the TV Introduction Remote control unit16 17 18 TV front viewTV rear view Preparation Supplied accessoriesAttaching the stand unit Confirm that there are eight screws with the stand unitClose the battery cover Using the remote control unitPreparation Inserting the batteries Turn on the Main Power switch on the left side of the TV Initial installation overviewQuick guide Start searching ChannelsSupplying power to the antenna Before turning on the powerQuick guide Mounting the TV on a wallDigital broadcast setting Initial auto installationConfirm the following before turning on the power Searching for terrestrial broadcastsTo change each item to the appropriate settings Analogue broadcast settingSettings and the connected antenna Searching for cable broadcastsChecking signal strength Checking signal strength and channel strength DVB-T/CInserting the CA card into the CI module Checking channel strengthDaily operation Watching TVDisplay range setup EPG setup setting for receiving EPG DataGenre icon setup Genre icon listWatching TV Selecting a programme using EPGWhat is teletext? Using the MHEG-5 application UK onlyTeletext Turning teletext on/offBefore connecting Connecting external devicesWhen using the Hdmi 2 terminal Video connectionsControlling devices with Scart using AV Link Connecting external devicesScart connection  Scart cableVideo connection PB PR Component connectionAudio connections Speaker/amplifier connectionAquos Link connection Controlling Hdmi devices using Aquos LinkBasic operation Aquos Link setupDisplaying Aquos Link menu Operating an Aquos Link deviceAquos Link menu Operation without a remote control unit What is the MENU?Menu operation About the guide displayPicture adjustments Basic adjustmentPicture settings AdvancedBasic adjustment Auto volume Audio adjustmentSurround Bass enhancerSleep timer No signal offECO picture control Energy saveProgramme setup Auto installationChannel settings Auto installationCable setting Manual adjustButtons for Manual adjust operation Erase programme SortKey lock Child lockQuick start Blue illuminationSelecting the picture size Useful viewing functionsMode REC picture size Useful viewing functionsLanguage SubtitleTime display Display settingsGame play time Programme title displayOther useful features Connecting a USB device Other useful featuresPhoto mode USB Photo viewer/Music playerSelecting the BGM Music modeSlide show USB device compatibilityConnecting a PC Connecting a PCDisplaying a PC image on the screen Selecting the picture sizeAdjusting the PC image automatically Connecting a PCAdjusting the PC image manually Auto syncRS-232C port specifications RS-232C command list Appendix TroubleshootingProblem Possible solution Reset Download setupAppendix Message listUpdating your TV via USB Software updateInformation on the software license for this product To complete the operationSTEREO/BILINGUAL NICAM/A2 SpecificationsAppendix Optional accessories Environmental specificationsRating table for child lock Broadcasted rating User-adjusted ratingAbbreviation list Abbreviated term Stands forEnd of life disposal 52o/46o Sharp Corporation