Pelco TLR2096 operation manual Mechanical, Gnd, General

Page 51

MECHANICAL
Heads
Video:	4 rotary single crystal heads
Audio/Control:	1 stationary head
Erase:	1 full-track head
Motors:	3 motors-drum/capstan direct drive system
Video Input:	1.0 Vp-p, 75 ohms, BNC plug
Audio Input:	-8 dBs, 50k ohms, RCA plug
Microphone Input:	-67 dBs, 600 ohms, mini mic jack
Video Output:	1.0 Vp-p, 75 ohms, BNC plug
Audio Output:	-6 dBs, 1k ohms, RCA plug
Connectors:
SET Input:	Screw terminal for starting alarm recording
RST Input:	Screw terminal for finishing alarm recording or for
	adjusting on-screen clock
REC Input:	Screw terminal for starting/finishing recording or for
	series recording
GND:	Screw terminal for ground
ALM Output:	Screw terminal for output while alarm recording is
	under way
CLK Output:	Screw terminal to command camera switching
MODE Output:	Screw terminal for indication of VCR selected mode
CALL Output:	Screw terminal for external warning device or for
	series recording
REMOTE Jack	Jack for connecting the remote control unit
GENERAL
Operating Temperature:	41°F-104°F (5°C to 40°C)
Relative Humidity:	Maximum 80%
Dimensions:	3.7”H x 16.7”W x 12.4”D (JOG dial included)
	(9.3 x 42.5 x 31.5 cm)
Weight:	10 lb (4.5 kg)

(Design and specifications are subject to change without notice.)

Pelco Manual C651M (7/99)

51

Image 51

Contents TLR2096 Contents Adjustment During Playback Timer RecordingAlarm Recording Recording After a Power Failure Playback Playback ProcedureManual # Date Comments List of IllustrationsList of Tables Revision HistoryAvertissement GeneralSAFEGUARDS, WARNINGS, CAUTION, and Care Power Cord Protection CleaningAccessories Power SourcesCare Of Video Cassette Tape Regulatory NoticesInformation Unpacking InstructionsTLR2096 Features and Functions OverviewIntroduction to TIME-LAPSE Recorders Pelco Manual C651M 7/99 Quick Start Basic StartAdditional Items Securing The VCR Controls InstallationPRE-INSTALLATION Cautions InstallationAudio Monitor MIC Audio Video OUTMX4000 Genex Series Multiplexer Connecting the VCR to a MultiplexerFor Automatic Speed TrackingB lines in Figure TIME-LAPSE VCR Coaxial CableFront Panel ControlsFluorescent Display Rear Panel This page intentionally left blank General Programming Instructions ProgrammingTime and Date Display Quick Guide to TLR2096 Menu StructureDisplay Menu 6.4.1 Display Mode Main MenuTime Date Size Direction Time Date Search MenuTime DateTimer Program Illustration Timer Program MenuRear Terminal Menu Recording SET UP MenuMaintenance Menu Day And Time Display Modes First Time SET UP MenuSet The Day And Time Display ModeTime Date Adjust Daylight Savings OFF Month Year Preventing Accidental Erasure LOADING/UNLOADING/PROTECTING the Tape CassetteLoading UnloadingRecording Mode RecordingManual Recording Repeat Recording Stop Rewind Repeat AlarmprotRecord Check Function Audio RecordingSeries Recording Recommended Number Of Tape UsesSynchronous Recording Timer Recording Programming ProcedureSpecial DW Settings Alarm Input Avoid Mistakes When Using The TimerAlarm Recording Symptom Fault ActionAlarm Recording Connection External Time Clock Adjustment1st VCR 2nd VCR Programming For Alarm Recording Emergency Recording Alarm Record Time DisplayReset The Alarm Recording List Recording After a Power FailurePlayback Procedure Playback ModePlayback Shuttle Ring Audio PlaybackEnd Of Tape Special Effects PlaybackDirect Shuttle Ring Still PictureFrame-By-Frame Playback Locating the Start of Alarm Recordings Index SearchSkip Search Tracking Adjustment Adjustment During PlaybackPicture Quality Adjustment Vertical AdjustmentSharp Counter Additional Functions and FeaturesMemory Backup in Case of Power Failure Power Failure Time DisplayElapsed Time Display Testing Initial System TestingRegular System Testing Troubleshooting SELF-DIAGNOSTIC Function and Warning DisplayMonitor Cause Remedy To turn off the indication Symptom Remedy Before Calling for ServiceSpecifications ElectricalVideo Mechanical GNDGeneral Warranty and Return Information WarrantyReturns