Sylvania LC200SL8A owner manual Watching TV, Channel Selection, To Use the Number buttons

Page 15

WATCHING TV

5Channel Selection

Select channels by pressing [CH. K/L] or [the Number buttons].

To select the memorized channels, use [CH. K/L] or [the Number buttons].

To select the non-memorized channels use [the Number buttons].

To Use [the Number buttons]

TV

- When selecting analog channel 12

DTV

-When selecting digital channel 12-1

Be sure to press [–/ENT.]before entering the minor channel number.

Press [CH. RETURN] to return to the previously viewed channel.

When you select a channel larger than 100, press [+100] first. Then use [the Number buttons] to press the lower 2-digit numbers.

About digital TV broadcasting:

With its high definition broadcast, digital broadcasting far surpasses analog broadcasting in both its picture and sound quality.

What is the minor channel?

By using high compression technology, digital broadcasting offers a service that enables multiple signals to send simultaneously.

Therefore, you can select more than one program per major channel since digital broadcasting technology distinguishes between multiple channels broadcast by a single network.

5Volume Adjustment

INTRODUCTION

 

This section describes how to adjust the volume. The mute function, which turns the sound off and on, is also described.

 

 

 

 

 

 

 

 

 

 

 

 

X Y

 

 

 

 

Use [VOL. / ] to adjust the audio volume.

CONNECTION

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOLUME

20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INITIAL

 

 

 

 

 

 

 

 

 

 

 

• The volume bar will be displayed at the bottom of the

 

TV screen when adjusting the volume.

 

 

 

SETTING

a few seconds.

 

 

 

• The volume bar display will automatically disappear in

 

 

 

 

 

 

 

 

 

 

 

 

 

Press [MUTE] to turn off and on the sound.

 

MUTE

20

 

WATCHING TV

 

 

 

 

 

 

 

• “MUTE” is displayed on the TV screen for a few

 

OPTIONAL

seconds.

 

 

 

X Y

 

 

 

 

 

 

Press [MUTE] again or [VOL. / ] to recover the

SETTING

original volume.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TROUBLESHOOTING

NTSC (analog mode) [Air Time] 18:00

 

18:30

CH4

19:00

 

19:30

 

20:00

 

20:30

ATSC (digital mode)

CH4

No signal

No signal

 

CH4

 

(high definition

TV)

CH4

CH4-1

No signal

CH4

No signal

CH4-2

CH4

CH4-1

CH4-2

INFORMATION

 

major channel

minor channel

: change automatically

: change manually by using [CH. K/L]

Although, you cannot watch the high definition TV (HDTV) program, the unit converts the HDTV signal down to the standard definition TV signal.

Note:

“NO SIGNAL” will appear on the TV screen after the minor channel broadcast is over.

15

EN

Image 15
Contents LC200SL8 a Important note is located on the rear of the cabinet IntroductionRADIO-TV Interference PrecautionsLocation Supplied AccessoriesSymbols Used in this Manual Tilt StandContents FeaturesInstalling the Batteries Remote Control FunctionRear Panel Control PanelAttach this unit to the wall Attaching a Wall Mount Bracket sold separatelyConnection to Cable Box or Satellite Box ConnectionBasic Connection Antenna Cable ConnectionExternal Device Connection Component Video Cable ConnectionVideo Cable Connection Digital Audio Output Connection Video ConnectionScanning and memorizing the channels automatically start Initial SettingInitial Setup Make sure if the unit is connected to antenna or cableAuto Channel Scan Main MenuPress Setup to exit Language SelectionEnglish Español Français To Use the Number buttons What is the minor channel?Watching TV Channel SelectionSAP Switching Each ModeSwitching Audio Mode MainPress Display Screen InformationLetterbox TV Screen Display ModeSleep Timer To Cancel the Sleep TimerChannel Add/Delete Optional SettingClosed Caption Picture AdjustmentTo select Caption SERVICE, then Press Enter repeatedly to change the settingTo select DTVCC, then press Dtvcc Style You can adjust color temperature of the TV screen Back Light SettingColor Temperature You can set the desired brightness modeUse Cursor K/L to select TV RATING, then press ChipTo select Mpaa RATING, then press Change the settingTo Set the Sub Ratings Association of AmericaEnter password again in Confirm PASSWORD. space Change PasswordTroubleshooting Guide TroubleshootingMaintenance Information Limited Warranty