Sylvania LC200SL8A owner manual Troubleshooting Guide

Page 27

TROUBLESHOOTING

5Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this owner's manual, check the following chart once before calling for service.

Symptom	Remedy
No power	• Be sure the power cord is plugged in.
	• If a power failure occurs, unplug the power cord for 30 minutes to allow the unit to
	reset itself.
No picture or sound	• Check if the power is on.
	• Check the outlet connection.
	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Turn off the power and wait for about 1 minute, then turn it on again.
No color	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
	• Adjust the “COLOR” in the main menu.
Sound OK, picture poor	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture distorted	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Weak picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Adjust “CONTRAST” and “BRIGHTNESS” in the main menu.
	• View other TV channels. The problem might be limited to the broadcasting station.
Lines or streaks in picture	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture blurred	• When the outside antenna is used, check the wire condition and connection.
	• View other TV channels. The problem might be limited to the broadcasting station.
Ghosts in picture	• Check the antenna or cable connection to the main unit.
	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Bars on screen	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
Picture rolls vertically	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Different color marks on	• Move the unit away from nearby electric appliances. Turn off the power and wait
screen	30 minutes before turning it back on.
	• View other TV channels. The problem might be limited to the broadcasting station.
Poor reception on some	• Check the antenna or cable connection to the main unit.
channels	• When the outside antenna is used, check the wire condition and connection.
	• Electrical interference from nearby appliances may affect picture quality.
	• View other TV channels. The problem might be limited to the broadcasting station.
Picture OK, sound poor	• View other TV channels. The problem might be limited to the broadcasting station.

No reception of digital signals	• Make sure auto channel scan has been completed (Refer to “Auto Channel Scan” on
	page 13).
	Auto channel scan must be completed when you set up the unit for the first time
	or move it to a location where previously unavailable channels are broadcast.
	• The selected channel may not be broadcasting.
	• When auto channel scan is interrupted and not completed, some channels will not
	be received. Make sure to complete (Refer to “Auto Channel Scan” on page 13).

INTRODUCTION CONNECTION INITIAL SETTING WATCHING TV OPTIONAL SETTING TROUBLESHOOTING INFORMATION

27

EN

Image 27

Contents LC200SL8 a Important note is located on the rear of the cabinet IntroductionRADIO-TV Interference PrecautionsLocation Supplied AccessoriesSymbols Used in this Manual Tilt StandContents FeaturesInstalling the Batteries Remote Control FunctionRear Panel Control PanelAttach this unit to the wall Attaching a Wall Mount Bracket sold separatelyConnection to Cable Box or Satellite Box ConnectionBasic Connection Antenna Cable ConnectionExternal Device Connection Component Video Cable ConnectionVideo Cable Connection Digital Audio Output Connection Video ConnectionScanning and memorizing the channels automatically start Initial SettingInitial Setup Make sure if the unit is connected to antenna or cableAuto Channel Scan Main MenuPress Setup to exit Language SelectionEnglish Español Français To Use the Number buttons What is the minor channel?Watching TV Channel SelectionSAP Switching Each ModeSwitching Audio Mode MainPress Display Screen InformationLetterbox TV Screen Display ModeSleep Timer To Cancel the Sleep TimerChannel Add/Delete Optional SettingClosed Caption Picture AdjustmentTo select Caption SERVICE, then Press Enter repeatedly to change the settingTo select DTVCC, then press Dtvcc Style You can adjust color temperature of the TV screen Back Light SettingColor Temperature You can set the desired brightness modeUse Cursor K/L to select TV RATING, then press ChipTo select Mpaa RATING, then press Change the settingTo Set the Sub Ratings Association of AmericaEnter password again in Confirm PASSWORD. space Change PasswordTroubleshooting Guide TroubleshootingMaintenance Information Limited Warranty