Sylvania LC370SS8 owner manual Initial Setting, 5Initial Setup

Page 13

INITIAL SETTING

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

INTRODUCTION

5Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and auto channel scan, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure if the unit is connected to antenna or cable.

1After making all the necessary connections, press [POWER] to turn on the unit.

• This operation may take a few moments.

2Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI i i l Setup

 

 

 

 

 

 

Select the language for setup display.

 

English

 

Elija el idioma de ajuste.

 

 

Español

 

 

 

Français

 

Sélectionner langue écran config.

 

 

 

 

 

 

 

Select

ENTER Enter

SETUP

 

Exit

 

 

 

 

 

“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].

3Use [Cursor K/L] to select “Air” for TV channels or “Cable” for CATV channels, then press [ENTER].

InitialI i i l Setup

Make sure the antenna is connected to "ANT.IN" jack.

Air

Select the destination of "ANT.IN" jack.

 

Cable

 

 

 

Air

 

 

 

Cable

Or

 

 

 

ANT.IN

 

 

 

 

Select

ENTER Enter

BACK

SETUP

Back

Exit

Scanning and memorizing of channels start automatically.

InitialI i i l Setup

Now the system is scanning for channels,please wait.

5%

Analog channels

1ch

 

 

 

 

 

 

 

 

Digital channels

0ch

 

 

 

 

 

 

 

SETUP

Exit

When the scanning and memorizing are completed, the lowest memorized channel in the broadcasting will be displayed.

Note:

If you connect the cable system directly, contact the CATV installer.

If you press [POWER] or [SETUP] during auto channel scan, this setting will be canceled.

The initial auto channel scan function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set auto channel scan again. (Refer to page 14.)

You can cancel or exit the initial auto channel scan menu by pressing [SETUP].

If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.

2-2

No channel is registered.

Press and hold "ENTER" key on the remote control for 3 seconds.

Contact support hotline provided on manual or back of unit.

Sin canal registrado.

Pulse durante 3 segundos la tecla "ENTER" en el control remoto.

Llame teléfono de apoyo en manual o atrás de TV.

Pas de chaîne consign.

Enfoncez "ENTER" 3 secondes sur la télécommande.

Contacter numero d'urgence dans manuel ou arrière appareil.

CONNECTION INITIAL SETTING WATCHING TV OPTIONAL SETTING TROUBLESHOOTING INFORMATION

13

EN

Image 13
Contents LC370SS8 To Receive DIGITAL/ANALOG SIGNAL, YOU Must Connect AntennaImportant note is located on the rear of the cabinet IntroductionRADIO-TV Interference Precautions5Symbols Used in this Manual 5Supplied AccessoriesQuick start guide Remote control LocationContents FeaturesDTV/TV/CATV 5Installing the Batteries 5Remote Control Function5Control Panel 5Basic Connection ConnectionAntenna Cable Connection Connection to Cable Box or Satellite BoxHdmi Connection 5External Device ConnectionHDMI-DVI Connection Video Cable Connection Component Video Cable ConnectionAudio Output Connection Digital Video ConnectionAnalog PC Connection 5Initial Setup Initial SettingMake sure if the unit is connected to antenna or cable Scanning and memorizing of channels start automatically5Auto Channel Scan 5Main MenuEnter 5Language SelectionWhat is the minor channel? 5Volume AdjustmentWatching TV 5Channel Selection5Switching Each Mode 5Still ModeYou can freeze the image shown on the TV screen This section describes how to switch the audio language 5Switching Audio ModeStereo SAPPress Info 5Screen InformationBroadcasting Information Day of Memories5TV Screen Display Mode Press Sleep to set the sleep timer 5Sleep TimerTo Cancel the Sleep Timer 5Channel List Optional SettingChannel l List 5Antenna Confirmation 5Manual RegisterUse the Number buttons or CH K/L to select Channel you want to add, then press Enter5Picture Adjustment You can adjust treble, bass and surround 5Sound AdjustmentAdjust the sound setting Treble, BassClosed Caption DTV CC 5DTV Closed CaptionUse Cursor K/L to select DTV CC, then press Enter DetaililFont Style 5CC StyleFont Size Font Opacity Font ColorBack Color Back OpacityChip Chipip Enter passwordChip ip Use Cursor K/L to select TV Rating, then press Association of AmericaTo Set the Sub Ratings ChipipChipip Enter password Confirm password Use Cursor K/L to select New Password, then press EnterClock, Phase 5PC SettingsHorizontal Position, Vertical Position You can set the method of sound input for the Hdmi 1-IN jack 5HDMI Audio5Troubleshooting Guide TroubleshootingRefer to IR Signal Check on Check the batteries of the remote controlDelayed behind the dialogue Entered channel numberInformation MaintenanceGlossary Atsc5Electrical Specification 5General Specifications5Other Specifications 5Cable Channel DesignationsMemo Limited Warranty
Related manuals
Manual 1 pages 35.39 Kb