Sylvania LC370SS8 owner manual 5Still Mode, 5Switching Each Mode

Page 17

5Still Mode

You can freeze the image shown on the TV screen.

Press [STILL] to pause the image shown on the screen.

Still

•The sound output will not be paused.

•If no signal is detected or protected signal is received during still mode, the image remains paused and the sound output will be muted.

•The still function will be released after 5 minutes.

To cancel still mode, press any button except [POWER].

5Switching Each Mode

You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access an external device when they are connected to the unit.

Press [INPUT SELECT] or [CH K] repeatedly to cycle through the input modes.

TV/DTV channel

Video1

or

Video2

Component1

Component2

HDMI1

HDMI2

PC

•Pressing [CH L] reverses the direction of the mode.

•To use the video or S-video input jack of VIDEO 1 on the unit, select “Video1”.

•To use the video or S-video input jack of VIDEO 2 on the unit, select “Video2”.

•To use the component video input jack of COMPONENT 1 on the unit, select “Component1”.

•To use the component video input jack of COMPONENT 2 on the unit, select “Component2”.

•To use the HDMI 1-IN jack on the unit, select “HDMI1”.

•To use the HDMI 2-IN jack on the unit, select “HDMI2”.

•To use the PC-IN jack on the unit, select “PC”.

INTRODUCTION CONNECTION INITIAL SETTING WATCHING TV OPTIONAL SETTING TROUBLESHOOTING INFORMATION

17

EN

Image 17

Contents LC370SS8 To Receive DIGITAL/ANALOG SIGNAL, YOU Must Connect AntennaImportant note is located on the rear of the cabinet IntroductionRADIO-TV Interference Precautions5Symbols Used in this Manual 5Supplied AccessoriesQuick start guide Remote control LocationDTV/TV/CATV FeaturesContents 5Installing the Batteries 5Remote Control Function5Control Panel 5Basic Connection ConnectionAntenna Cable Connection Connection to Cable Box or Satellite BoxHDMI-DVI Connection 5External Device ConnectionHdmi Connection Video Cable Connection Component Video Cable ConnectionAnalog Video ConnectionAudio Output Connection Digital PC Connection 5Initial Setup Initial SettingMake sure if the unit is connected to antenna or cable Scanning and memorizing of channels start automatically 5Auto Channel Scan 5Main MenuEnter 5Language SelectionWhat is the minor channel? 5Volume AdjustmentWatching TV 5Channel SelectionYou can freeze the image shown on the TV screen 5Still Mode5Switching Each Mode This section describes how to switch the audio language 5Switching Audio ModeStereo SAPPress Info 5Screen InformationBroadcasting Information Day of Memories5TV Screen Display Mode To Cancel the Sleep Timer 5Sleep TimerPress Sleep to set the sleep timer Channel l List Optional Setting5Channel List 5Antenna Confirmation 5Manual RegisterUse the Number buttons or CH K/L to select Channel you want to add, then press Enter5Picture Adjustment You can adjust treble, bass and surround 5Sound AdjustmentAdjust the sound setting Treble, BassClosed Caption DTV CC 5DTV Closed CaptionUse Cursor K/L to select DTV CC, then press Enter DetaililFont Size 5CC StyleFont Style Font Opacity Font ColorBack Color Back OpacityChip ip Chipip Enter passwordChip Use Cursor K/L to select TV Rating, then press Association of AmericaTo Set the Sub Ratings ChipipChipip Enter password Confirm password Use Cursor K/L to select New Password, then press EnterHorizontal Position, Vertical Position 5PC SettingsClock, Phase You can set the method of sound input for the Hdmi 1-IN jack 5HDMI Audio5Troubleshooting Guide TroubleshootingRefer to IR Signal Check on Check the batteries of the remote controlDelayed behind the dialogue Entered channel numberInformation MaintenanceGlossary Atsc5Electrical Specification 5General Specifications5Other Specifications 5Cable Channel DesignationsMemo Limited Warranty

Related manuals

Manual 1 pages 35.39 Kb