Camco 1550E, 950E, 2050E, 1150E service manual CAM Removal, CAM Installation

Page 14

CAM REMOVAL:

1.Once the input shaft has been removed, use one of two methods to lower the cam into the bottom of the housing.

1.1.Use a lift ring on the end of the treaded rod and a boom crane to lift the cam slightly, i. e. to relieve strain on the hex nut. Then while using the lift ring to support the cam, loosen the hex nut and back it off several inches. Use the boom crane to lower the cam into the bottom of the housing. See sketch titled "E-Series Input Shaft and Cam Removal" in this Service Manual.

1.2.Or without using a lift ring (no access for a boom crane), slowly loosen the hex nut and lower the cam into the bottom of the housing.

CAUTION

See "Approximate Weights" within this service manual for sizing the lifting device. Make sure the cam is supported.

2.Once the cam is sitting on the bottom of the housing, remove the threaded rod, etc.

3.Use one of two methods to get the cam out of the housing cavity.

3.1.Place a "Nylon Strap" through the bore of the cam, and while pulling on the strap, roll the cam out of the housing.

3.2.Alternatively, insert a piece of threaded rod with a lift ring into the tapped hole in the cam and using the lift ring, pull the cam out of the housing cavity.

CAM INSTALLATION:

Instructions for replacing the cam assume the follower wheel was not removed.

Before proceeding with installation of the new cam, install all but two new cam followers. Manually pull the follower wheel into a posi-

tion where one or more cam followers are over the housing cavity. Use a come-a-long or other device to pull the follower wheel and any attached tooling into position. Two or three cam followers can be accessed through the large access opening in the housing. See section titled "Cam Follower Replacement" in this Service Manual.

Do not install the last two (2) cam followers until the input shaft and cam have been installed.

Once all but two (2) cam followers have been replaced, place the cam inside the housing cavity.

1.Before placing the cam inside the housing cavity, check the input shaft diameter and the cam bore size to ensure a slip fit.

1.1.The input shaft can be installed in the cam and then removed to ensure a slip fit.

1.2.If the input shaft binds during installation, hone the cam bore to provide a slip fit.

CAUTION

The cam must be a slip fit or slight press fit, but the fit cannot be loose. Do not remove an excessive amount of material.

2.The cam can be either rolled into the hous- ing cavity, or it can be lifted and pushed into the housing cavity. Use the best method as determined by the situation.

3.Regardless of the method used to place the cam in the housing cavity, placing the cam into the housing cavity will be an awkward process.

CAUTION

Make sure the cam is not damaged during this process.

4.Install threaded rod and lift ring into the lift- ing hole in the cam. Then lift the cam so the input shaft can be pushed through the cam.

13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Heavy Duty Series Index Drives Models Table of Contents Introduction Spare Parts KIT Torque Requirements for Tightening Screws Inspection Disassembly and InspectionDisassembly OIL Seal Removal OIL Seal ReplacementOIL Seal Installation CAM Follower Removal CAM Follower ReplacementCAM Follower Replacement Series Index Drives CAM Follower Installation Series Input Shaft and CAM Removal CAM AND/OR Input Shaft ReplacementInput Shaft Removal Page Page Page CAM Installation CAM RemovalInput Shaft Installation Setting CAM Input Preload TorquePage Follower Wheel Removal Dwell POSITION, E-SERIES Index DrivesOutput Bearing Installation Output Bearing RemovalFinal Assembly Follower Wheel InstallationOn NON-WARRANTY HOW to Order PartsOn Warranty Required Information950E, 1150E, 1550E, & 2050E Parts List 950E Index Drive Standard Configuration Parts List 1150E Index Drive Standard Configuration Parts List 1550E Index Drive Standard Configuration Parts List 2050E Index Drive Standard Configuration USA 5/00

950E, 1550E, 2050E, 1150E specifications

Camco, an industry leader in innovative recreational vehicle (RV) and marine products, offers a range of portable waste tanks designed for convenience and efficiency. The Camco 1150E, 2050E, 1550E, and 950E are key products in this lineup, each designed with unique features and technologies to cater to different user needs.

The Camco 1150E is a robust 11-gallon portable waste tank made from high-density polyethylene. Featuring a patented, heavy-duty design, it can be easily transported and features integrated wheels for smooth maneuverability. The tank includes a large capacity dump valve and a 3" sewer hose with a 90-degree elbow, making emptying a simple and mess-free process. This model also comes with a built-in indicator to alert users when it’s time to empty, ensuring hassle-free maintenance.

The Camco 2050E is a larger 20-gallon option that offers enhanced capacity for extended trips. This model boasts a durable construction resistant to punctures and UV damage, ensuring longevity in various environments. The 2050E is designed with an extra-wide opening for easier filling and features a user-friendly tow design that ensures stability during transport. Its integrated handle and sturdy wheels allow for effortless movement, even on uneven surfaces.

The Camco 1550E is a middle-ground solution with a 15-gallon capacity, perfect for those who need more than the 11-gallon but less than the 20-gallon capacity. It features the same heavy-duty construction found in the 1150E and 2050E models, ensuring durability. It includes a level indicator to gauge fill levels and is designed for easy cleaning post-use, featuring smooth surfaces that reduce dirt accumulation.

Lastly, the Camco 950E is the most compact option at a 9-gallon capacity. Its lightweight design makes it ideal for short trips or users with limited storage space. Despite its smaller size, it retains the essential features such as a 3" drain hose, an easy-grip handle, and sufficient capacity for less frequent RV users.

Each tank in the Camco lineup offers high-quality construction, user-friendly features, and advanced technology to enhance the RV experience. Whether it’s the larger capacity of the 2050E or the compact design of the 950E, Camco has tailored their products to meet a range of consumer needs while ensuring ease of use and maintenance.
Top Page Image Contents