Camco 950E, 2050E, 1550E, 1150E service manual Final Assembly, Follower Wheel Installation

Page 20

3.Thread lifting eyes into the threaded holes in the bearing (two places 180 degrees apart or three places 120 degrees apart) and using a boom crane or hoist set the bearing onto the housing.

4.Coat the dowel pin holes with anti-seize lubricant and drive the dowel pins through the bearing and into the housing.

5.Apply Red Perma-Lok‚ and install 16 to 40 socket head cap screws. Tighten to specifi- cation. See "Metric Screw Tightening Torques" in this Service Manual.

FOLLOWER WHEEL INSTALLATION:

Prior to installing the follower wheel proceed as follows. Replace all cam followers in the follower wheel. See the section titled "Cam Follower Installation" in this Service Manual. Install cam and input shaft if they were removed. See the section titled "Cam and Input Shaft Installation" in this Service Manual. Clean and deburr all parts before re-assembly. Follow tightening torque and Perma-Lok®‚ recommendations as outlined in this Service Manual and the "General Service Manual".

1.Install follower wheel using the following steps.

1.1.Use a boom crane or hoist to lower the follower wheel into the pilot on the output bearing.

1.2.With the cam in place, be sure to posi- tion the followers on either side of the cam rib. The cam must be just entering dwell and at the start of motion.

Note: For most Camco E-Series Index Drives this is ten to fifteen (10˚ - 15˚) degrees clock- wise or counter-clockwise from the mid-dwell position. Refer to the model number of your Index Drive for the amount of dwell provided. Also refer to "Interpretation of Index Drive Model Number" in the General Service Manual.

1.3.If used, install pull type dowel pins. Apply Red Perma-Lok.

1.4.Install 16 to 40 socket head cap screws. Tighten to specification. See table titled “Torque Requirements For Tightening Screws” in this Service Manual.

FINAL ASSEMBLY:

1.Reinstall the Large Access Cover.

1.1.Apply a thin bead of "General Electric Silicone Rubber RTV-6" or equivalent to the housing area where the cover seats.

2.Fill the index drive with recommended oil to level indicated by the Sight Glass. Lubricating oils should be high quality, well refined petroleum oils or synthetic lubri- cants with extreme pressure additives. They may be subjected to high operating temperatures, so they must have good resistance to oxidation. These oils should meet the American Gear Manufactures Association (AGMA) standards, AGMA 4 EP or AGMA 5 EP. Two such oils are:

Mobil's, Mobilgear 630, AGMA 5 EP

Mobil's, Mobil Synthetic oil SHC634,

AGMA 8 EP

See "General Service Manual" for compete lubrication specifications.

A slightly high oil level will cause no damage. Too low a level may result in unit failure.

3.Lubricate the output bearing with grease. Use grease that conforms to NGLI #2 or NGLI #3. One such grease Is:

Mobil's Mobillith AW2

See "General Service Manual" for compete lubrication specifications.

4.Adequate grease can be maintained in a reused bearing by lubricating with four- (4) oz. of grease. The bearing must be rotating while lube (grease) is injected into

19

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Heavy Duty Series Index Drives Models Table of Contents Introduction Spare Parts KIT Torque Requirements for Tightening Screws Inspection Disassembly and InspectionDisassembly OIL Seal Removal OIL Seal ReplacementOIL Seal Installation CAM Follower Removal CAM Follower ReplacementCAM Follower Replacement Series Index Drives CAM Follower Installation Series Input Shaft and CAM Removal CAM AND/OR Input Shaft ReplacementInput Shaft Removal Page Page Page CAM Installation CAM RemovalInput Shaft Installation Setting CAM Input Preload TorquePage Follower Wheel Removal Dwell POSITION, E-SERIES Index DrivesOutput Bearing Installation Output Bearing RemovalFinal Assembly Follower Wheel InstallationHOW to Order Parts On WarrantyOn NON-WARRANTY Required Information950E, 1150E, 1550E, & 2050E Parts List 950E Index Drive Standard Configuration Parts List 1150E Index Drive Standard Configuration Parts List 1550E Index Drive Standard Configuration Parts List 2050E Index Drive Standard Configuration USA 5/00

950E, 1550E, 2050E, 1150E specifications

Camco, an industry leader in innovative recreational vehicle (RV) and marine products, offers a range of portable waste tanks designed for convenience and efficiency. The Camco 1150E, 2050E, 1550E, and 950E are key products in this lineup, each designed with unique features and technologies to cater to different user needs.

The Camco 1150E is a robust 11-gallon portable waste tank made from high-density polyethylene. Featuring a patented, heavy-duty design, it can be easily transported and features integrated wheels for smooth maneuverability. The tank includes a large capacity dump valve and a 3" sewer hose with a 90-degree elbow, making emptying a simple and mess-free process. This model also comes with a built-in indicator to alert users when it’s time to empty, ensuring hassle-free maintenance.

The Camco 2050E is a larger 20-gallon option that offers enhanced capacity for extended trips. This model boasts a durable construction resistant to punctures and UV damage, ensuring longevity in various environments. The 2050E is designed with an extra-wide opening for easier filling and features a user-friendly tow design that ensures stability during transport. Its integrated handle and sturdy wheels allow for effortless movement, even on uneven surfaces.

The Camco 1550E is a middle-ground solution with a 15-gallon capacity, perfect for those who need more than the 11-gallon but less than the 20-gallon capacity. It features the same heavy-duty construction found in the 1150E and 2050E models, ensuring durability. It includes a level indicator to gauge fill levels and is designed for easy cleaning post-use, featuring smooth surfaces that reduce dirt accumulation.

Lastly, the Camco 950E is the most compact option at a 9-gallon capacity. Its lightweight design makes it ideal for short trips or users with limited storage space. Despite its smaller size, it retains the essential features such as a 3" drain hose, an easy-grip handle, and sufficient capacity for less frequent RV users.

Each tank in the Camco lineup offers high-quality construction, user-friendly features, and advanced technology to enhance the RV experience. Whether it’s the larger capacity of the 2050E or the compact design of the 950E, Camco has tailored their products to meet a range of consumer needs while ensuring ease of use and maintenance.
Top Page Image Contents