Camco 2050E, 950E, 1550E, 1150E service manual CAM Follower Installation

Page 9

4.Remove bore plug (Item #33), the cam follower screw (Item #15) and the heavy washer (Item #9). CAMCO used Red Perma-Lok‚ to secure these screws If you encounter difficulty when removing the screw, apply heat to the screw and remove while still warm.

CAUTION

Localized heat can distort the part. Do not overheat any item.

5.Using a large soft faced hammer, drive the cam follower downward and out through the follower wheel.

6.Inspect each cam follower stud hole for roundness and size. The cam follower stud hole must be a interference fit. The cam follower holes must be -.0005 to -

.0010 inch for the full length of the hole. Check the follower holes for roundness. These holes should be round within .0005 TIR of an inch to permit reuse of the follower wheel. These holes may be worn-out due to overloads.

CAUTION

Do not use a follower wheel with oversize fol- lower holes. The cam followers and cam will fail prematurely.

CAM FOLLOWER INSTALLATION:

The instructions for replacing cam followers assume the follower wheel and cam were not removed. Cam followers will be installed one at a time through the follower access hole in the housing. If the follower wheel was removed, proceed by repeating the first four steps until all cam followers have been installed in the follower wheel.

If the cam was removed but not the follower wheel, proceed by repeating the first four steps until all but two cam followers have been replaced. Also see additional instruc- tions below.

WARNING

Use protective gloves while handling cam fol- lowers after they have been packed in dry ice.

1.Coat the follower wheel stud hole with anti-seize lubricant. Using quick sure movements, place a cam follower that has been packed in dry ice for at least three (3) hours into the follower wheel hole.

1.1.Using a twisting motion of the hand, push the cam follower upward hard enough to press the cam follower into the follower wheel hole. Make sure the shoulder on the cam follower seats against the follower wheel. Do not rush the process; just proceed quickly and with sure movements.

1.2.If the cam follower cannot be seated by using a twisting motion of the hand and pushing upward, use a soft faced hammer to drive the cam follower into the follower wheel.

1.3.Alternatively, pull the cam follower into place using the cam follower screw, heavy washer and tapped hole in the cam follower stud.

1.4.In a worst case, place a steel plate against the bottom of the cam follower and use a hydraulic jack to push the cam follower into the follower wheel.

CAUTION

Make sure the shoulder of the cam follower is seated against the follower wheel and make sure the follower is installed straight and in line with the hole. Damage to the cam follower, follower wheel or cam could occur if cam follower is improperly aligned during installation.

8

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Heavy Duty Series Index Drives Models Table of Contents Introduction Spare Parts KIT Torque Requirements for Tightening Screws Disassembly and Inspection DisassemblyInspection OIL Seal Replacement OIL Seal InstallationOIL Seal Removal CAM Follower Replacement CAM Follower Replacement Series Index DrivesCAM Follower Removal CAM Follower Installation CAM AND/OR Input Shaft Replacement Input Shaft RemovalSeries Input Shaft and CAM Removal Page Page Page CAM Removal CAM InstallationInput Shaft Installation Input Preload Torque Setting CAMPage Dwell POSITION, E-SERIES Index Drives Follower Wheel RemovalOutput Bearing Removal Output Bearing InstallationFollower Wheel Installation Final AssemblyOn Warranty HOW to Order PartsOn NON-WARRANTY Required Information950E, 1150E, 1550E, & 2050E Parts List 950E Index Drive Standard Configuration Parts List 1150E Index Drive Standard Configuration Parts List 1550E Index Drive Standard Configuration Parts List 2050E Index Drive Standard Configuration USA 5/00

950E, 1550E, 2050E, 1150E specifications

Camco, an industry leader in innovative recreational vehicle (RV) and marine products, offers a range of portable waste tanks designed for convenience and efficiency. The Camco 1150E, 2050E, 1550E, and 950E are key products in this lineup, each designed with unique features and technologies to cater to different user needs.

The Camco 1150E is a robust 11-gallon portable waste tank made from high-density polyethylene. Featuring a patented, heavy-duty design, it can be easily transported and features integrated wheels for smooth maneuverability. The tank includes a large capacity dump valve and a 3" sewer hose with a 90-degree elbow, making emptying a simple and mess-free process. This model also comes with a built-in indicator to alert users when it’s time to empty, ensuring hassle-free maintenance.

The Camco 2050E is a larger 20-gallon option that offers enhanced capacity for extended trips. This model boasts a durable construction resistant to punctures and UV damage, ensuring longevity in various environments. The 2050E is designed with an extra-wide opening for easier filling and features a user-friendly tow design that ensures stability during transport. Its integrated handle and sturdy wheels allow for effortless movement, even on uneven surfaces.

The Camco 1550E is a middle-ground solution with a 15-gallon capacity, perfect for those who need more than the 11-gallon but less than the 20-gallon capacity. It features the same heavy-duty construction found in the 1150E and 2050E models, ensuring durability. It includes a level indicator to gauge fill levels and is designed for easy cleaning post-use, featuring smooth surfaces that reduce dirt accumulation.

Lastly, the Camco 950E is the most compact option at a 9-gallon capacity. Its lightweight design makes it ideal for short trips or users with limited storage space. Despite its smaller size, it retains the essential features such as a 3" drain hose, an easy-grip handle, and sufficient capacity for less frequent RV users.

Each tank in the Camco lineup offers high-quality construction, user-friendly features, and advanced technology to enhance the RV experience. Whether it’s the larger capacity of the 2050E or the compact design of the 950E, Camco has tailored their products to meet a range of consumer needs while ensuring ease of use and maintenance.
Top Page Image Contents