Loewe R 37 Full-HD+ 100, R 37 HD+ 100 Explanations of the setting possibilities, DVB-S cable

Initial installation

Explanations of the setting possibilities:

Location	Select the country for country-specific pre-settings.
of TV set	If UK or IRL is selected for the location of TV set, it is pos-
	sible to activate MHEG-5 (UK Freeview) for the TV set.
	A dialogue appears, where you can confirm to set the
	operating software to the selected location.
	If Yes is selected and confirmed with OK, the TV set turns
	off and on again automatically. First installation starts
	again after activating the operation software.
	If MHEG-5 was activated, DVB-C and DVB-S can not be
	used anymore. Only terrestrial/cable and DVB-T stations
	are available.
Antenna	Antenna/cable (analogue): analogue stations via
selection	DVB-T:	cable/antenna
		digital terrestrial stations
	DVB-C:	digital stations via cable
	DVB-S (cable 1):	digital stations via satellite
	DVB-S (cable 2):	digital stations via satellite
Encrypted	You can state whether coded stations are to be searched
stations	for in the search/update. Select yes then coded stations
	are also searched for. However, these stations can only
	be received in connection with a CA module and the
	appropriate Smart Card. Handling of the CA module is
	described on page 35.
DVB-T:	If you are using an active antenna, then select yes (5V)
Antenna	for the antenna power supply.
DVB-C:	The conventional settings will be derived from the selection
Settings	of set location. Only change this if you know other symbol
	rates and modulation types or if you have to specify the
	network ID for your cable network (information available
	from your cable network provider). If you want to run the
	station search independently of the channel grid, select
	frequency search for the search method.
DVB-S:	Select which satellite(s) you receive from a list. For more
Satellite	than one satellite, select the type of your changeover
system	switch or communal satellite system additionally.
	Ask your dealer in this regard.
High band	Specify here whether the high band of the selected satellite
	is to be searched in addition to the low band.

LNC	Normally, you do not need to change the values for high
frequencies	and low band, unless the LNC (LNB) of your satellite
Low Band /	system uses a different oscillator frequency (important
High Band	for the frequency display).
	After you have made these settings, you should receive
	the picture and sound of the selected satellites (only with
	Astra1 and HOTBIRD).
Search	If you want to run the station search independently of
method	the channel grid, select frequency search for the search
	method.
Symbol rates	The symbol rates are specified by the satellite provider
	and normally do not need to be changed.
Favoured	Select the signal source that provides the stations to be on
signal source	top of your station list (starting with station slot 1).
Start search	Start the automatic station search with OK.
	First TV stations, then radio stations are searched for.
	The stations found in the automatic search are divided
	into the appropriate station blocks depending on the
	previously selected antenna cables (signal sources). Sub-
	sequently the stations can only be re-sorted within these
	blocks. At the beginning of the station list you will find the
	block with the stations of the preferred signal source.
	Any mixed sorting of stations from different signal sources
	is only possible with the favourites list.
	➠ For TV sets with MHEG-5 software the stations are
	tied to “Logical Channel Numbers” – “LCN” and
	sorted from 1-799. Digital stations without “LCN” are
	stored from 800 onwards. Analogue stations are stored
	from 1001.
Connecting	Then the connection and sound component wizard
additional	starts which helps you to log in, set and connect video
devices	recorders, decoders, a loudspeaker system or a HiFi/AV
	amplifier to your TV set. DVD players and DVD recorders
	are already registered at the factory.
	You can start the connection wizard and the sound
	components wizard manually later and add new devices.
	Further information is available from page 40 (Connection
	wizard) and page 47 (Sound components wizard).

continued on next page Ž

- 12