Copying the recorded data
This item is used to copy the data to a copy device.
Copy Data to Copy 1 Drive/Set Copy 1 Drive
This item is used to copy the data to Copy 1 device by speci- fying the start and end points. The points are specified by the date and time or the bookmark. This function is useful for copying the data of the short period of time.
Before executing the copy, make sure that the Copy 1 device is connected and set in the <Add/Remove HDD Device> and <Add/Remove DVD/CD Drive> correctly. (System Menu Memory)
User Menu
2 Copy
steps 4, 5
1 Copy Data to Copy 1 Drive
step 3
1 + 2 Range of Copy
steps 1, 2
3 Set Copy 1 Drive
step1. Set the camera number to be copied.
•The button function changes between “All Off” and “All On” each time you select this button. You can switch on and off for all the cameras easily by using this button.
•The picture is not copied when there is no recorded picture of the set camera number or time. Make sure to check that the picture of the specified camera has been recorded on the specified copy start point.
step2. Select “Other settings” and then set the detailed settings.
From Device: Sets the device which contains the data to be copied. The available setting items are “Main” and “Copy 2.”
From Group: Sets the group which contains the data to be copied. The available setting items are “Normal,” “Alarm,” and “LPA” for main, “SerialBus,” “DVD/CD,” and “Internal” for copy 2.
To Copy 1: Sets the group to where the data is copied. The available setting items are “SerialBus,” “DVD/CD,” and “USBmemory.”
Copy Data: Sets the data area to be copied. The available setting items are “Alarm” and “All.” Overwrite: Selects whether or not to overwrite the existed data.
Auto Eject: Selects whether to eject media (CD/ DVD) automatically when the copy is over.
“Alarm” appears for “From Group” when “Alarm Recording Area” is set to other than “0 %.” (System Menu Memory Data Management Setting for Main Memory)
“LPA” appears for “From Group” when “Long Pre-Alarm Area” is set to other than “0 %.” (System Menu Memory Data Management Setting for Main Memory)
During copy 2 operation, data cannot be copied from copy 2 device to copy 1 device. Stop copy 2 operation first and then copy the data to copy 1 device.
When copying the data to DVD while “Overwrite” is set to “On,” the unit clears the existing data on the disc before overwriting with new data. Note that clearing the data takes about 30 to 40 minutes. You cannot cancel opera- tion during clearing the data of the DVD.
When copying the data while “Copy Data” is set to “Alarm,” the unit performs copy operation, however, the data is not copied if there is no alarm recording data within the speci- fied range of copy. In case of CD/DVD disc, the remaining capacity becomes low because only the management information is recorded. It is recommended to carry out “Calculate” in <Copy Data to Copy 1 Drive> to confirm whether or not there is alarm recording data in the speci- fied range.
step3. Select <Copy Data to Copy 1 Drive> and select “Start,” “Start/End,” or “End” and then select “Set.” Input the start/end time or select the bookmark of copy.
Start: Sets only the start point of copy. The data is copied from the specified start point as much data as possible with the remaining capacity of the media to be copied.
Start/End: Sets the start and end points of copy. When the amount of data to be copied is larger than the capacity of a single CD/DVD disc, copy all the desired data to multiple CD/DVD discs according to the direction from the recorder. In the case of copying to a USB memory or HDD, only the amount of data equal to the available free space on the copy destination media is copied. It is recommended to check whether all the desired data have been copied properly after the copy is finished.
End: Sets only the end point of copy. The data is copied as much data as possible with the remaining capacity of the media to be copied until the specified end point reaches.
•To set the bookmark point, select “Bookmark” and then select the desired bookmark number.
•To copy from the oldest recording time, select “Copy Start Time.” To copy to the latest recording time, select “Copy End Time.”
step4. Select “Calculate” to calculate the capacity of data to be copied.
When using “End,” the copy cannot be executed unless the calculation of the capacity of data to be copied is com- pleted.
When using “Start” or “Start/End” and executing copy without calculating the capacity of data to be copied, the progress or the time of the copy may not be displayed correctly because the unit cannot determine the capacity of data to be copied.
In the case of copying to a USB memory or HDD, when the amount of data to be copied is larger than the availa- ble free space on the copy destination media, the estimat- ed copy data volume indicates the remaining capacity of the copy destination media. It is recommended to check whether all the desired data have been copied properly after the copy is finished.
step5. Select “Execute.”
•The copy starts.
•To stop copy manually, select “Cancel” in the progress screen. The data which has been copied before cancelling is copied.