Panasonic AJ-D650 Rec Cue, ST1, Output, ST2, PB Fade, T O, Embedded, Aud, Line CH, Pcm, Int Sg

USER menu

<AUDIO> (continued)

	Item			Setting
							Description
No.	Superimposed		No.		Superimposed
	display					display
716	REC CUE	0000				CH1	This selects the input signal recorded in CUE.
		0001				CH2	0: The signal selected by SETUP-MENU No.714 is recorded
		0002				CH1+2	on CH1.
							1: The signal selected by SETUP-MENU No.715 is recorded
							on CH2.
							2: The signal selected by SETUP-MENU No.714 and
							No.715 are mixed and recorded on CH1 and CH2.
718	DV		0000			ST1	This selects the AUDIO CH1 and CH2 output signals during
	OUTPUT	0001				ST2	DV format playback.
		0002				ST1+2	0: The CH1 track signals are output to CH1 and the CH2
							track signals to CH2. (Only the sound during shooting is
							output.)
							1: The CH3 track signals are output to CH1 and the CH4
							track signals to CH2. (Only the audio dubbing sound is
							output.)
							2: The mixed CH1 and CH3 track signals are output to CH1
							and the mixed CH2 and CH4 track signals to CH2. (The
							sound during shooting and audio dubbing sound are
							output simultaneously.)
	<Note> This item setting is valid only when the tape recorded on the four channels of the DV format is
	played back.
719	PB FADE	0000				A U T O	This selects the processing method for the audio edit points
		0001				CUT	(IN point, OUT point) during playback.
		0002				FADE	0: According to the status during recording. (Setup menus
							No.309, 310)
							1: Forced CUT
							2: Forced FADE
720	EMBEDDED	0000				OFF	This selects whether to superimpose the audio data onto the
	AUD	0001				ON	serial output.
							0: Data is not superimposed.
							1: Data is superimposed.
	<Note> This item is valid when the optional serial interface board has been installed.
721	LINE CH		0000			PCM	This selects the audio output (LINE OUT).
	SEL	0001				AUTO	0: PCM AUDIO or QUICK PCM AUDIO is output.
							1: Whatever is selected by SETUP-MENU No.713 (MONI
							CH SEL) output.
	<Note> The PCM AUDIO or QUICK PCM AUDIO output is not affected by the AUDIO MONITOR
	SELECT SW, and CH1 and CH2 are output independently.
722	INT SG		0000			OFF	This selects whether the internal signal is to be used for the
		0001				ON	audio input signal.
							0: The internal signal is not selected.
							1: The internal signal is selected.
	<Note> The internal signal has a frequency of 1 kHz.
723	DV PB ATT		0000			OFF	This selects the audio output level for DV format playback.
		0001				ON	0: The audio output level is attenuated (reduced).
							1: The audio output level is not attenuated.
	<Notes> As indicated below, whether the setting takes effect or not depends on the size of the cassette
	tape used.
	1. When an “L” size cassette is used
	The setting takes effect only when “DV” has been selected as the setting for setup menu
	No. 108 (FORMAT SEL).
	2. When an “M” size cassette is used
	The setting does not take effect.
	3. When an “S” size cassette is used
	The setting takes effect.

The underline on the setting item denotes the initial setting.

– 3 7 –