Panasonic PV-D4742, PV-D4752 manual Important Safeguards and Precautions

Page 2
ELECTRIC
SERVICE EQUIPMENT
GROUND
CLAMP
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM
(NEC ART 250, PART H)
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ANTENNA
LEAD IN WIRE

Important Safeguards and Precautions

FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE UNIT

INSTALLATION

1POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.

2POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a three-wire grounding type plug.

POLARIZED PLUG CAUTION:

This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION:

This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.

3POWER CORD

Make sure power cords are routed so that they are not likely to have anything rest on them, roll over them, or be in the way of walking traffic.

If an extension cord is used, make sure it also has either a polarized or grounded plug and that the cords can be securely connected.

Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified service technician. Overloaded outlets and extension cords are fire hazards and should be avoided.

4DO NOT BLOCK VENTILATION HOLES Ventilation openings in the cabinet release heat generated during operation. If they are blocked, heat build-up inside the unit can cause failures that may result in a fire hazard or heat damage to cassettes or discs.

For protection, follow these rules:

a.Never cover ventilation slots or the unit while in use, or operate the unit when placed on a bed, sofa, rug, or other soft surface.

b.Avoid built-in installation, such as a book case or rack, unless proper ventilation is provided.

5PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or radiator, in direct sunlight, inside closed vehicles, in high temperature [over 104°F (40°C)], or in over 75% humidity. If the unit is suddenly moved from

acold place to a warm one, moisture may condense in the unit and on the tape causing damage. Never subject the unit to vibration, impact, or place it so that the surface is titled as internal parts may be seriously damaged.

6TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping surface.

• Do not place this unit on any support that is not

firm, level, and adequately strong. The unit could fall causing serious

injury to a child or adult and damage to the unit.

• An appliance and cart combination should be moved

with care. Quick stops, excessive force, and uneven

surfaces may cause the appliance and cart combination to overturn.

Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.

OUTDOOR ANTENNA INSTALLATION

1SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static

charges and voltage surges.

ELECTRICAL CODE

 

NEC - NATIONAL

Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada,

part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

2KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.

USING THE UNIT

If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.

1KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT, unplug the unit and have it inspected by a qualified service technician before use.

3DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4WHEN THE UNIT IS PLUGGED IN

Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.

Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard.

Do not put any foreign object on the disc tray.

Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.

5USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

SERVICE

1DO NOT SERVICE THIS PRODUCT YOURSELF If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.

2IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacture’s service literature to ensure that the unit is in safe operating condition.

2

Image 2
Contents Guía para rápida consulta en español está incluida PV-D4752 onlyImportant Safeguards and Precautions FCC Caution Region Management InformationInside of product Disc Handling Before UsingAccessories Loading the BatteriesTable of Contents Deck & Cassette Information Specifications Definition of Terms DVDNumber keys Remote ControlLocation of Controls Bold Italic VCR and DVD FunctionsFast FORWARD/SEARCH Play REWIND/SEARCH Front View of DeckSTOP/EJECT Channel / TRACKING/V-LOCK VCR/TV RECRear View of Deck To enjoy Progressive Scan video PV-D4752 onlyMulti Function Display Displays On Screen & Multi FunctionOn Screen Displays VCR DSS Receiver Deck TV Deck TV Cable Box Deck TV ConnectionsBasic Connections OUTWith a Cable Box Deck Cable Box TV Connections For DVD OnlyOther Connections You Can Connect With Two Cable BoxesDeck Amplifier Speaker Ready ChecklistAudio Connections DVDTo Optical Digital Audio Input Connector Firmly connect the cable to the connectorPlugging the AC Power Plug into an AC outlet Before doing Initial SetupDoing Initial Setup Ready to Play Turn TV onIf Auto Clock Set was incomplete Manual Clock SetAction Select SET Press ACTION* on remote to display Clock screenTo display Menu Reset Language, Channels, ClockPress Action Add or Delete a Channel Power VCRVCR’s Output Channel DST Daylight Saving TimePlayback/ Record on a Tape Ready ChecklistEJECTDVDPlayback using Deck buttons REW/SLOWRecord using Deck buttons Press OPEN/CLOSE Operation using Deck buttonsBasic DVD Operation Press or Number keys see below to select title,Resume Function Auto-Power Off FunctionSurround Sound System ADD/DLT Prog Select Timer RecordingPower VCR Operation Audio Receivable Broadcast TypesDisplay Audio Mode for Recording Audio Mode for PlaybackUsing Multi-Brand Control Multi-Brand Control FeatureMulti-Brand Control Setup Hitachi/ Hughes MagnavoxTape Operation Index Search Program End SearchAuto Play Auto Operation FunctionsCommercial Skip Auto RewindZero Search Display Stop Action Select SET CM/ZERO Counter ResetRepeat Play Auto Shut-Off Feature VCR Lock FeatureWeak Signal Display Feature To turn on, hold down REC onInput Stop PAUSE/ Still Action Select SET Tape Position REC Special VCR FeaturesTape Position and Tape Status Feature Press Tape PositionCopying Your Tapes Dubbing Playing Source VCR Recording Editing DeckAudio Soundtrack Language DVD only Disc OperationSubtitle Language DVD only Press SUB TitlePress Angle Multiple Angle Viewing DVD onlyPicture Zoom DVD only To select the desiredPress Title Title Menu DVD onlyDVD Menu DVD only Press SET or PlayProgram Play Video CD/CD Program Repeat Play Video CD/CDPress to select Setting the Sound Output LevelRandom Play Video CD/CD Music CDTo return to normal DVD OperationPress ScreenDisc information screen for Video CD/ CD Detailed Descriptions of each On-Screen DisplayDisc information screen for DVD Deck information screen for DeckSingle Repeat Play Mode NormalMP3 Playback Folder RepeatPress Action twice DVD Lock DVD onlyPress Number keys to enter your secret code Settings for DVD Operation Disc Languages DVD onlyDolby Digital selections Audio OutputLpcm DVD selections Dts selectionsExample Still ModeTV Mode 9072 Chinese 8373 Singhalese 9085 Zulu Language Code ListCode Language If you press REC on the remote control or If you attempt to set or review a TimerBefore a Timer Recording is about to Begin If you press Stop or PowerRemote Control Correction Before Requesting ServicePower Correction Recording & Playback CorrectionMiscellaneous Correction Be sure disc is installed with label side upDVD/ Video CD/ CD Correction Servicenter List Limited Warranty PANASONIC/QUASAR Video ProductsConectando Conexiones/Configuracion Inicial Ready to PlayRealizando configuracion inicial Para Ant/Cable-DECK-TVProgramación fácil para la grabación con temporizador Grabación normal 030Operaciones básicas del DVD Para volver a la pantalla normal Presione repetidamente Clear o DisplaySelección de Idiomas DEL Disco DVD solamente Cambio del idioma de la pista de sonido DVD solamenteFijaciones iniciales Cambio del idioma de subtítulos DVD solamenteSelección de vocal para los discos de Karaoke DVD/Video CD Visión desde otro ángulo DVD solamenteUtilización de un menú de títulos DVD solamente Utilización de un menú de DVD DVD solamenteIndex Deck & VCR