Pelco C636M-F manual Connections

Page 19

CONNECTIONS

Refer to Figure 8.

1.Connect the viewstation to the recorder via an Ethernet switch. Use shielded network cables.

NOTE: Use a shielded cable, similar to Belden 1533P, that meets or exceeds the support requirements for ANSI/TIA/EIA 568B.2 Cat 5e.

2.Connect a monitor, keyboard, and mouse to the viewstation.

3.Connect cameras to the video input coaxial connectors on the recorders, and then set the termination switches to Term (75 ohms). This is the factory default.

4.Connect looping video sources, such as monitors, to the video output coaxial connectors on the recorder and then set the switches to Loop (HI-Z). You can then terminate at the final devices.

5.Connect a CM9760-REL, CM9760-ALM, or CM9760-DT to the RS-232 COM port. Refer to the Advanced Features section.

6.Wire alarms and relays. Refer to the Wiring Alarms and Relays section.

7.Plug the HASP (Hardware Against Software Piracy) USB key into the bottom right USB port on the recorder. A red light on the key indicates that it is working properly. The key contains the product license and its configured permissions. The following message appears if you do not plug in the HASP key:

Figure 7. Hasp Key Message

8.Connect a monitor, keyboard, and mouse to the recorder. You can remove them after setup is complete.

9.Connect all power cords.

NOTE: The audio inputs on the rear of the recorder are reserved for future use.

C636M-F (3/09)

19

Image 19
Contents DX9100 Series Contents C636M-F 3/09 List of Illustrations 100 List of Tables Important Safety Instructions DX9100DVR Series Regulatory NoticesDescription DX9100VSR ModelsFront View of Recorder Front View RecorderBack View of Recorder Back View RecorderFront View of Viewstation Front View ViewstationBack View of Viewstation Back View ViewstationWindows 2000 license label on unit Installation Guidelines Mounting DX9100 Rack Mount Installation Connections System Connections Wiring Alarms and Relays Power UP the Equipment Programming Viewstation Network ConfigurationChanging the VIEWSTATION’S Identification Viewstation Local Area Connection Status Dialog Box Changing the VIEWSTATION’S IP Address and Subnet MaskClick Properties. The following dialog box appears Changing the RECORDER’S Identification Time Synchronization Time Zone Setting DATE/TIME PropertiesClient Configuration Utility C636M-F 3/09 Recorder Initialization Options DX9116F Frame Rate and ResolutionC636M-F 3/09 Go to Start Programs DX9000 Viewstation Server State Server StateError Alert Advanced Recorder Options Database Backup and RepairSystem Tray Database RestorationMy Computer Window Databases Window Rename Mssql to MSSQLold Mssql Folders Delete MSSQLold C636M-F 3/09 Restore Utility Dialog Box Go to the system tray Start/Continue Window C636M-F 3/09 Finished Scan Dialog Box Alarm Modes/Relay Intervals Dialog Box Configuring Standard Alarm and Relay PropertiesCamera Properties Dialog Box Camera Recording PropertiesContinuous Recording Schedule Daily Recording Schedule Continuous Recording ScheduleDaily Event Recording Continuous Weekly Recording Schedule Weekly Recording ScheduleMotion Detection Motion DetectionCamera Video Setup Channel SetupParameter Description/Action User Manager Dialog Box Defining UsersEdit Existing Users Handler InterfaceManager Recorder Connecting AN Alarm UnitCM9760 Alarm Driver Dialog Box Select CM9760ALM.dll Alarm Unit ConfigurationClick Open. The following dialog box appears Manager for Alarm Unit Sample Configuration for External 1 Source Click Next. The following dialog box appears Connecting a CM9760-REL Connecting a Relay UnitCM9760 Relay Driver Dialog Box Select CM9760REL.dll Relay Unit ConfigurationClick Open. The following dialog box appears Manager for Relay Unit Click Next. The following dialog box appears CM9760-DT Connecting a CM9760-CC1Connecting a CM6800 Connecting a CM6800CM9760 Data Translator Driver Dialog Box Select CM9760DT.dll Data Translator ConfigurationClick Open. The following dialog box appears Manager for Data Translator Click Next. The following dialog box appears Data Translator Connections DVR ManagementConfiguring the Data Translator Click Configure. The following dialog box appears Relay Unit Connections Connecting a CM9760-REL for DVR ManagementConfiguring the Relay Unit Click Configure. The following dialog box appears Foreign Language Programming Click Set Default. The following dialog box appears Specifications Viewstation Product Warranty and Return Information