JVC HR-J246EK, HR-J645ES, HR-J645EK, HR-J245EK instruction manual Timer Recording, Timer again

Page 47

47

4. Camcorder recording is not	● The camcorder has not been	Confirm that the camcorder is
possible.	properly connected.	properly connected.
	● The input mode is not correct.	Set the input mode to “AU”.

	TIMER RECORDING

		SYMPTOM			POSSIBLE CAUSE		CORRECTIVE ACTION
	1.	Timer recording won’t work.			● The clock and/or the timer have		Re-perform the clock and/or timer
					been set incorrectly.		settings.
					● The timer is not engaged.		Press TIMER and confirm that “ä“ is
							displayed on the display panel.

	2.	On-screen timer programming is			● Timer recording is in progress.		Timer programming can’t be
		not possible.					performed while a timer recording is
							in progress. Wait until it finishes.

	3.	“ä“ and “]“ on the display			● The timer is engaged but there’s no		Load a cassette with the Record
		panel won’t stop blinking.			cassette loaded.		Safety tab intact, or cover the hole
							using adhesive tape.

	4.	The cassette is automatically			● The loaded cassette has had its		Remove the cassette and cover the
		ejected, and “ä“ and “]“ on the			Record Safety tab removed.		hole with adhesive tape, or insert a
		display panel won’t stop blinking.					cassette with the Record Safety tab
							intact.

	5.	“ä“ blinks for 10 seconds and the			● TIMER has been pressed when there		Check the programmed data and re-
		Timer mode is disengaged.			are no programs in memory, or the		program as necessary, then press
					timer record information has been		TIMER again.
					programmed incorrectly.

	6.	The cassette is automatically			● The end of the tape was reached		The programme may not have been
		ejected, the power shuts off and			during timer recording.		recorded in its entirety. Next time make
		“ä“ and “]“ won’t stop					sure you have enough time on the tape
		blinking.					to record the entire programme.

	7.	Video Plus+ does not timer-record			● The recorder’s preset positions have		Refer to "Guide Program Number Set"
		properly.			been set incorrectly.		and re-perform the procedure
							(☞ pg. 10).

	OTHER PROBLEMS

		SYMPTOM			POSSIBLE CAUSE		CORRECTIVE ACTION
	1.	Whistling or howling is heard from			● The camcorder’s microphone is too		Position the camcorder so its
		the TV during camcorder record-			close to the TV.		microphone is away from the TV.
		ing.			● The TV’s volume is too high.		Turn the TV’s volume down.

	2.	When scanning channels, some of			● Those channels have been desig-		If you need the skipped channels,
		them are skipped over.			nated to be skipped.		restore them (☞ pg. 38).

	3.	The preset cannot be changed.			● Recording is in progress.		Press PAUSE to pause the recording,
							change presets, then press PLAY to
							resume recording.

	4.	The remote control won’t operate a			● The TV/SAT./VCR switch is in the		Set the switch to the correct position.
		JVC TV.			wrong position.

	5.	Channel settings that were made			● After the manual settings were		Perform manual setting again.
		manually seem to have changed or			made, Auto Channel Set was
		disappeared.			performed.

	6.	No channels are stored in the			● The TV aerial cable was not		Connect the TV aerial cable to the
		recorder's memory.			connected to the recorder when		recorder properly and turn off the
					Auto Set Up was performed.		recorder power once, then turn the
							recorder power back on again. The
							recorder will try Auto Set Up again
							(☞ pg. 8).

Image 47

Contents Instructions Do not place the recorder Safety PrecautionsStep Quick SET UP Connect Recorder to Mains Check ContentsBasic Connections Situate RecorderBack of HR-J245EK/J246EK Back of HR-J645EK/ESWith RF Connection Video Channel SetWith AV Connection Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelPerform Auto SET UP Auto Set UpIf auto channel set has succeeded but auto clock set has not Screen Video Plus+ SetupMake List of Stored Station Names Preset Positions Access Main MenuBack Confirm Preset Position NumberWhen Using a Satellite Receiver And/Or Cable System Close MenuStart Playback Basic PlaybackLoad a Cassette PointPlayback Playback FeaturesSearch Activate HIGH-SPEED SearchReturn to Automatic Adjust TrackingOverride Automatic Tracking ManuallyMemory Activate Index SearchSET Counter Memory Activate CounterSoundtrack Selection HR-J645EK/ES only Activate RepeatRepeat Playback Ntsc Playback Next Function MemoryBasic Recording Recording Features Recording S.T. Picture SystemReturn to Normal Playback PDC Recording Video Plus+ Timer RecordingPress OK after entering If your recorder receivesTime Regular Timer ProgrammingAccess Programme Start TimePress TV PROG. + Timer ModeEngage RECORDER’S Information Check And Cancel ProgrammesTimer Warning Revise ProgrammeAuto Timer Access Main Menu ScreenStart Source Player SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsRecorder Player HR-J245EK/J246EKPlayer RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderConnection To Stereo System HR-J645EK/ES only Satellite Receiver Unit Connection To a Satellite ReceiverPin Scart connectors Aerial terminal 13 3 Access Mode SET ScreenTurn on the Recorder On-Screen DispiayType of Broadcast On-screen Display Being Received Tape Position IndicatorPerform Auto Channel SET Auto Channel SetLocated appear on a Preset positions PRProcedures Stations your recorderManual Channel Set Select NEW Position Change Station Preset PositionSelect Item Delete ChannelEnter NEW Character Switch StationsSelect NEW Station Select Station Name CharacterFINE-TUNE Perform TuningFine-Tuning Channels Already Stored Select Channel toStation Name TV Station And ID ListScotland TV Station Channel Number Guide For customers in the U.KPreparation Clock SetTurn the Recorder on SET Just Clock PresetSET Clock SET Date and TimeTroubleshooting Timer again Timer RecordingQuestions and Answers Specifications Index Rear View J645EK/ES Display Panel Remote Control Operating JVC TVs Installing BatteriesHow To Use Memo Victor Company of JAPAN, Limited