JVC HR-J935EK specifications Engage Insert Editing, Start Editing, END Insert Editing

Page 39

INSERT

PLAY

			8
• •	• • •	• •	• • •
•	•	•	•
• •	• •	• •	• •
			A. DUB

i

	2
1	2	3
4	5	6
7	8	9
C.RESET	0
C.RESET
		PLAY

3

1

								39
								39

		6		ENGAGE INSERT EDITING
				Press INSERT.

				● Your recorder enters the Insert-Pause mode.
				● The TV screen changes from the still picture to the
				input source you are going to record.

		7		START EDITING
				Load the source cassette and play back the segment
				that is to be inserted. When you reach the start of the
				section of the source tape that you wish to insert, press
				PLAY to start the tape in your recorder; Insert Editing
				begins at this point.

		8		END INSERT EDITING
				At counter "0:00:00", Insert Editing will stop automati-
				cally while the tape continues running in the Play
				mode. if you wish to stop Insert Editing before the
				specified edit-out point, press C.RESET.

FOR AV INSERT EDITING

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time...

In step 6 above, after you press INSERT, press A. DUB also.

NOTES:

●Suitable leads can be obtained from your dealer.

●Insert editing is not possible with cassettes whose safety tab has been removed.

●In insert editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording's speed changes within a single edit, the inserted picture will be distorted at the switching point.

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel AV1 IN/ OUT or AV2 IN connector. When using these connectors, make sure to select the correct input mode in step 2.

●Connections made to the recorder's front panel are given priority over those made to the rear panel connectors.

Image 39

Contents HR-J935EK Safety Precautions Safety FirstDo not place the recorder Step Quick SET UP Situate Recorder Check ContentsInstalling Your N EW Recorder Basic ConnectionsTune The TV To Your Video Recorder Select Output ModeSET TV Preset Reset Output ModeUnit Connection To Satellite ReceiverInst Allin G Your NEW RE C Order contd Satellite ReceiverConnection To Stereo System Make ConnectionsAudio OUT View Confirmation Screen Access CH SET Mode MenuTuner Set Turn on the RecorderPreparation Clock SetTurn the Recorder on SET Clock AutomaticallySET Just Clock PresetInitial Settings SET Date and TimePlayback BasicFeatures PlaybackActivate HIGH-SPEED Search Activate Instant Review Adjust Tracking ManuallyOverride Automatic Tracking Return to Automatic TrackingNext Function Memory Tape Position IndicatorActivate Index Search Index SearchActivate Counter Activate Scene FinderStop Scene Finder SET Counter MemoryTrack USE Ntsc PlaybackSoundtrack Selection During PlaybackDisplay Remaining Time SET A/B Code SwitchRE-SUPPLY Power Remote A/B Code SwitchingVariable-Speed Search/ Reverse Play Audio signal during TimeScanTime Scan Shuttle Indicator Time Scan Indicator TimeScanTimeScan Speed SP Speed LPAudio output Recording Confirm B.E.S.T. Status Access Mode SelectS.T. Picture System RecordingRecording ON-SCREEN Display ENABLE/DISABLEClose Mode Select On-Screen DisplaysReceiving Nicam Stereo And Bilingual Programmes Recording FeaturesSelect Preset to Watch Record One Programme While Watching AnotherSET Counter Display Reset CounterEngage ITR Mode Adjust Audio Recording LevelGuide Channel Set Access CH. SET Mode Menu ScreenTimer Recording Information On Video Plus+Enter Preset Position NumberClose Menu When Using The Illumi-Guide Feature Video Plus+ Timer RecordingTimer RECORDINGcont Access Timer PROGRAM- Ming ScreenSatellite Receiver Users Timer ModeReturn to Normal Engage RECORDER’SPress Prog Regular Timer ProgrammingAccess Programme Screen Will come on automaticallyPress TV PROG. + Engage RECORDER’S Timer ModeTime TV Prog ++/-, Date +/- and TV PROG. +/- buttons on Check And Cancel ProgrammesTimer Warning Revise Programme IN- FormationPDC Recording TimerAuto SP/LP Timer Engage Auto SP/LPStart Recording Deck SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderLocate EDIT-IN Point Access R.A. Edit FunctionRandom As- semble Editing Prepare for EditingPrepare Recording Deck Locate EDIT-OUT PointStart R.A. Edit END R.A. EditSET Input Mode Reset the CounterLocate Start Point Engage Insert Editing Start EditingEND Insert Editing END Audio Dubbing Audio DubbingEngage Audio Dubbing Start DubbingMake sure to select the correct input mode in step TRY Operating TV Control Your TV Using Addi- tional ButtonsMulti-Brand Remote Con- trol SET TV Brand CodeSelect Position Access CH. SET ModeSelect Mode MenuSelect NEW Position Change Station Preset PositionSelect Item Delete ChannelEnter NEW Character Switch StationsSelect NEW Station Select Station Name CharacterSelect Channel to Perform TuningFine-Tuning Channels Already Stored Access Manual CH. SETStation Name TV Station and ID ListTV STA T ION Channel Number G Uide Back TroubleshootingPanel Indicator off If you are using the AV connectionTimer again R OubleshootingCamcorder recording is not Camcorder has not been Questions and Answer S Ä remain lit on the display panel. Is there a problem?Maximum recording time SpecificationsMulti-Brand Remote MBR Control Setting IndexList Of Terms Front View Open the lid to access covered connectors and buttonsTime Scan Audio Switch enables/disables TimeScan Audio. pg Rear View Display Panel Remote Control How To Use Installing BatteriesHR-J935EK