JVC HR-J935EK specifications Recording, Playback

Page 22

22

PAUSE

PLAY

					8
• •	•	• •	• •	•	• •
•		•	•		•
• •		• •	• •		• •

RECORD

	2
1	2	3
4	5	6
7	8	9
	0
	PLAY

PAUSE

RECORD

3

1

RECORDING(cont.)

NOTES:

●The B.E.S.T. system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording.

●In the case of timer recording, the B.E.S.T. system works before recording is initiated.

●Once the cassette is ejected, the B.E.S.T. data is cancelled. The next time the cassette is used for recording, B.E.S.T. is re- performed.

ATTENTION:

Since the B.E.S.T. system works before recording actually starts, there is a delay of approximately 7 seconds after RECORD and PLAY on the remote are pressed, or RECORD on the recorder is pressed. To make sure you record the desired scene or programme in its entirety, first perform the following steps:

1)Press and hold PAUSE and RECORD to engage the RECORD PAUSE mode.

●The recorder then automatically checks the condition of the tape and, after approximately 7 seconds, re- enters RECORD PAUSE.

2)Press PLAY to start recording.

●If you want to bypass the B.E.S.T. system and begin recording immediately, set “B.E.S.T.” to “OFF” in step 3 on page 21.

Playback

The recorder assesses the quality of the tape once you initiate playback. When watching a tape recorded with “B.E.S.T.” set to “ON”, it is recommended that you leave B.E.S.T. on during playback as well.

START PLAYBACK

1 Press PLAY.

●The recorder adjusts the playback picture quality based on the quality of the tape in use.

●B.E.S.T. is active during Auto Tracking. “BEST” appears blinking on the recorder’s display panel.

NOTES:

●When watching a rental tape, or one recorded on another video recorder, set B.E.S.T. to your preference by performing steps 2 through 4 on page 21.

●"BEST" only appears at the beginning of automatic tracking. Even though it doesn't appear after that, the B.E.S.T. function is operative.

Image 22

Contents HR-J935EK Safety First Safety PrecautionsDo not place the recorder Step Quick SET UP Basic Connections Check ContentsInstalling Your N EW Recorder Situate RecorderReset Output Mode Select Output ModeSET TV Preset Tune The TV To Your Video RecorderSatellite Receiver Connection To Satellite ReceiverInst Allin G Your NEW RE C Order contd UnitMake Connections Connection To Stereo SystemAudio OUT Turn on the Recorder Access CH SET Mode MenuTuner Set View Confirmation ScreenSET Clock Automatically Clock SetTurn the Recorder on PreparationSET Date and Time PresetInitial Settings SET Just ClockBasic PlaybackPlayback FeaturesActivate HIGH-SPEED Search Return to Automatic Tracking Adjust Tracking ManuallyOverride Automatic Tracking Activate Instant ReviewIndex Search Tape Position IndicatorActivate Index Search Next Function MemorySET Counter Memory Activate Scene FinderStop Scene Finder Activate CounterDuring Playback Ntsc PlaybackSoundtrack Selection Track USERemote A/B Code Switching SET A/B Code SwitchRE-SUPPLY Power Display Remaining TimeTimeScan Audio signal during TimeScanTime Scan Shuttle Indicator Time Scan Indicator Variable-Speed Search/ Reverse PlaySpeed SP Speed LP TimeScanAudio output Recording Recording Access Mode SelectS.T. Picture System Confirm B.E.S.T. StatusRecording On-Screen Displays ENABLE/DISABLEClose Mode Select ON-SCREEN DisplayRecord One Programme While Watching Another Recording FeaturesSelect Preset to Watch Receiving Nicam Stereo And Bilingual ProgrammesAdjust Audio Recording Level Reset CounterEngage ITR Mode SET Counter DisplayInformation On Video Plus+ Access CH. SET Mode Menu ScreenTimer Recording Guide Channel SetNumber Enter Preset PositionClose Menu Access Timer PROGRAM- Ming Screen Video Plus+ Timer RecordingTimer RECORDINGcont When Using The Illumi-Guide FeatureEngage RECORDER’S Timer ModeReturn to Normal Satellite Receiver UsersWill come on automatically Regular Timer ProgrammingAccess Programme Screen Press ProgTV Prog + Engage RECORDER’S Timer ModeTime Press TV PROG. +Revise Programme IN- Formation Check And Cancel ProgrammesTimer Warning +/-, Date +/- and TV PROG. +/- buttons onEngage Auto SP/LP TimerAuto SP/LP Timer PDC RecordingStart Source Player SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Recording DeckStart Camcorder SET RECORDER’S Input ModeEdit From a Camcorder Start RecorderPrepare for Editing Access R.A. Edit FunctionRandom As- semble Editing Locate EDIT-IN PointEND R.A. Edit Locate EDIT-OUT PointStart R.A. Edit Prepare Recording DeckReset the Counter SET Input ModeLocate Start Point Start Editing Engage Insert EditingEND Insert Editing Start Dubbing Audio DubbingEngage Audio Dubbing END Audio DubbingMake sure to select the correct input mode in step SET TV Brand Code Control Your TV Using Addi- tional ButtonsMulti-Brand Remote Con- trol TRY Operating TVMenu Access CH. SET ModeSelect Mode Select PositionDelete Channel Change Station Preset PositionSelect Item Select NEW PositionSelect Station Name Character Switch StationsSelect NEW Station Enter NEW CharacterAccess Manual CH. SET Perform TuningFine-Tuning Channels Already Stored Select Channel toTV Station and ID List Station NameTV STA T ION Channel Number G Uide If you are using the AV connection TroubleshootingPanel Indicator off BackR Oubleshooting Timer againCamcorder recording is not Camcorder has not been Ä remain lit on the display panel. Is there a problem? Questions and Answer SSpecifications Maximum recording timeIndex Multi-Brand Remote MBR Control SettingList Of Terms Open the lid to access covered connectors and buttons Front ViewTime Scan Audio Switch enables/disables TimeScan Audio. pg Rear View Display Panel Remote Control Installing Batteries How To UseHR-J935EK