JVC HR-J935EK Questions and Answer S, Ä remain lit on the display panel. Is there a problem?

Page 51

QUESTIONSANDANSWERS

51

PLAYBACK

RECORDING

Q. What happens if the end of the tape is reached during playback or search?

A. The tape is automatically rewound to the beginning.

Q. Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Other than preventing further recording, what effect does removing the Record Safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the video recorder indefinitely remain in the Record-Pause mode?

A. No. The video recorder shuts off automatically after 5 minutes to protect the heads.

Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the

beginning.

TIMER RECORDING

Q. " " and "ä" remain lit on the display panel. Is there a problem?

A. No. This is a normal condition for a timer recording in progress.

Q. Can I program the timer while I’m watching a tape or a TV broadcast?

A. You won’t see the picture as it is replaced by the on- screen menu, but the audio from the program or tape you’re viewing can be heard.

ATTENTION:

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 51

Contents HR-J935EK Safety Precautions Safety FirstDo not place the recorder Step Quick SET UP Situate Recorder Check ContentsInstalling Your N EW Recorder Basic ConnectionsTune The TV To Your Video Recorder Select Output ModeSET TV Preset Reset Output ModeUnit Connection To Satellite ReceiverInst Allin G Your NEW RE C Order contd Satellite ReceiverConnection To Stereo System Make ConnectionsAudio OUT View Confirmation Screen Access CH SET Mode MenuTuner Set Turn on the RecorderPreparation Clock SetTurn the Recorder on SET Clock AutomaticallySET Just Clock PresetInitial Settings SET Date and TimePlayback BasicFeatures PlaybackActivate HIGH-SPEED Search Activate Instant Review Adjust Tracking ManuallyOverride Automatic Tracking Return to Automatic TrackingNext Function Memory Tape Position IndicatorActivate Index Search Index SearchActivate Counter Activate Scene FinderStop Scene Finder SET Counter MemoryTrack USE Ntsc PlaybackSoundtrack Selection During PlaybackDisplay Remaining Time SET A/B Code SwitchRE-SUPPLY Power Remote A/B Code SwitchingVariable-Speed Search/ Reverse Play Audio signal during TimeScanTime Scan Shuttle Indicator Time Scan Indicator TimeScanTimeScan Speed SP Speed LPAudio output Recording Confirm B.E.S.T. Status Access Mode SelectS.T. Picture System RecordingRecording ON-SCREEN Display ENABLE/DISABLEClose Mode Select On-Screen DisplaysReceiving Nicam Stereo And Bilingual Programmes Recording FeaturesSelect Preset to Watch Record One Programme While Watching AnotherSET Counter Display Reset CounterEngage ITR Mode Adjust Audio Recording LevelGuide Channel Set Access CH. SET Mode Menu ScreenTimer Recording Information On Video Plus+Enter Preset Position NumberClose Menu When Using The Illumi-Guide Feature Video Plus+ Timer RecordingTimer RECORDINGcont Access Timer PROGRAM- Ming ScreenSatellite Receiver Users Timer ModeReturn to Normal Engage RECORDER’SPress Prog Regular Timer ProgrammingAccess Programme Screen Will come on automaticallyPress TV PROG. + Engage RECORDER’S Timer ModeTime TV Prog ++/-, Date +/- and TV PROG. +/- buttons on Check And Cancel ProgrammesTimer Warning Revise Programme IN- FormationPDC Recording TimerAuto SP/LP Timer Engage Auto SP/LPStart Recording Deck SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Start Source PlayerStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderLocate EDIT-IN Point Access R.A. Edit FunctionRandom As- semble Editing Prepare for EditingPrepare Recording Deck Locate EDIT-OUT PointStart R.A. Edit END R.A. EditSET Input Mode Reset the CounterLocate Start Point Engage Insert Editing Start EditingEND Insert Editing END Audio Dubbing Audio DubbingEngage Audio Dubbing Start DubbingMake sure to select the correct input mode in step TRY Operating TV Control Your TV Using Addi- tional ButtonsMulti-Brand Remote Con- trol SET TV Brand CodeSelect Position Access CH. SET ModeSelect Mode MenuSelect NEW Position Change Station Preset PositionSelect Item Delete ChannelEnter NEW Character Switch StationsSelect NEW Station Select Station Name CharacterSelect Channel to Perform TuningFine-Tuning Channels Already Stored Access Manual CH. SETStation Name TV Station and ID ListTV STA T ION Channel Number G Uide Back TroubleshootingPanel Indicator off If you are using the AV connectionTimer again R OubleshootingCamcorder recording is not Camcorder has not been Questions and Answer S Ä remain lit on the display panel. Is there a problem?Maximum recording time SpecificationsMulti-Brand Remote MBR Control Setting IndexList Of Terms Front View Open the lid to access covered connectors and buttonsTime Scan Audio Switch enables/disables TimeScan Audio. pg Rear View Display Panel Remote Control How To Use Installing BatteriesHR-J935EK