JVC HR-J755EK setup guide Video Plus+ Timer Programming

Page 12

12BASICOPERATIONS (cont.)

Video Plus+

Timer

Programming

Before performing Video Plus+ Timer Programming:

●Make sure that the recorder's built-in clock is set properly.

●Insert a cassette with the safety tab in place. The recorder will come on automatically.

●Turn on the TV and select the VIDEO channel (or AV mode).

– –:– –

With Video Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.

ACCESS VIDEO PLUS+ SCREEN

1	Press PROG.	VIDEO PLUS+
	Press PROG.

		[0 – 9] =
		[+/–] : EXPRESS PROGRAMING
		[PROG] : EXIT

The front display panel looks like this:

ENTER PLUSCODE NUMBER

	Press the NUMBER keys to	VIDEO PLUS+
	enter the PlusCode	VIDEO PLUS+
	enter the PlusCode	1 2 3 4 5 6 7 8
	2 number of the programme	1 2 3 4 5 6 7 8
	2 number of the programme
	you wish to record.

2

NUMBER

5 PDC

STOP+/–

1,6 PROG

1

4

7

1

2	DAILY
	3

2

5 6

8 9 WEEKLY

0 4 7

SP/LP	4

●If you make a mistake, press and input the

	correct number.	[0 – 9] =
	correct number.	[ ] : DELETE
		[ ] : DELETE
		[PROG] : EXIT

The PlusCode number you enter appears on the front display panel:

The display panel shows only a 4-digit number.

ACCESS VIDEO PLUS+ PROGRAM SCREEN

Press OK, and the Video		– P1 –
Plus+ Program screen	VIDEO PLUS+ 123456789
3 appears (if you’re just	START	STOP

3

OK 3,6

starting out, “P1” appears).		21:00		= 22:00
starting out, “P1” appears).			SP	VPS/PDC OFF
			SP	VPS/PDC OFF
The display panel shows the			DATE		TV PROG
programme start time.		25.12		1
Pressing	changes the				BBC 1
Pressing	changes the
display to the programme			: OK
stop time, then the date and
preset position.

			SP

IMPORTANT

Make sure the preset position number you wish to record is displayed; if not, see "Video Plus+ Setup" on page 44 and set the Guide Program number for that PlusCode number correctly.

●If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel. Press and input a valid PlusCode number.

●If the "GUIDE PROG SET" screen appears, see "ATTENTION – Regarding Guide Program Number Set" on page 13.

Image 12

Contents HR-J755EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV TV Aerial Cable not providedMains outlet Back of RecorderYour TV via both an RF cable and a 21-pin Go to itemIf auto channel set has succeeded but auto clock set has not Playback Load a CassettePoint Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode Display Remaining TimeVideo Plus+ Timer Programming Timer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Playback Picture Adjustment Looking For Scene You Want Activate Index SearchSkip Over Unwanted SectionsActivate Instant Review Instant ReViewPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Selecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedActivate Spatializer SpatializerAerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Link SP/LPTV Multi-brand Remote Control Control Your TV Using Additional ButtonsRemote Con- trol Functions SET TV Brand CodeSET Remote Control Code RE-SUPPLY PowerSET Satellite Receiver Brand Code Operate Satellite ReceiverInput Mode Edit To Or From Another Video RecorderMake Connections SET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto SP→LP Timer Auto TimerReturn to Normal Screen Activate Repeat PlaybackRepeat Playback Next Function MemoryConnection To Stereo System Audio Cable not provided Speaker Mains outletAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelTest Signal With RF ConnectionAccess Main Menu Tuner SetSET Auto Channel SetScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Access Manual Channel SET Screen Select NEW StationClose Confirmation Select Station Name CharacterTV Station And ID List TV Station Channel Number Guide Channel IslandsWinter Hill Clock Set Just ClockVideo Plus+ Setup NumberGuide Program Number Set Questions And Answers PlaybackTroubleshooting No power is applied to the recorderConnect the mains power cord Indicator offTimer Recording Won’t stopIndex Front ViewRear View Remote Control How To Use Specifications DA4 Double Azimuth helical