JVC HR-J755EK setup guide Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 34

34SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

STOP

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 6).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

●If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV Connection" below.

●If you have connected the video recorder to your TV via an RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 35.

– –:– –

With AV Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

1 2 3

4 5 6

7 8 9

0

1

2

4

TV PROG

OK

ACCESS VIDEO CHANNEL SET MODE

1	Press and hold down STOP on the recorder until the
	display panel shows the following.


2	SET VIDEO CHANNEL
	Press TV PROG – until the display panel shows
	"–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 34

Contents HR-J755EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Mains outlet Back of TVTV Aerial Cable not provided Back of RecorderYour TV via both an RF cable and a 21-pin Go to itemIf auto channel set has succeeded but auto clock set has not Point PlaybackLoad a Cassette Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter Display Remaining TimeVideo Plus+ Timer Programming Timer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Playback Picture Adjustment Skip Over Unwanted Looking For Scene You WantActivate Index Search SectionsActivate Instant Review Instant ReViewTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Soundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Type of Broadcast On-screen Display Being ReceivedActivate Spatializer SpatializerOutdoor Unit Satellite Cable Aerial connectorAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Link SP/LPRemote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverEdit To Or From Another Video Recorder Input ModeMake Connections Start Camcorder SET RECORDER’S Input ModeEdit From a Camcorder Start RecorderENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsAuto Timer Auto SP→LP TimerReturn to Normal Screen Repeat Playback Activate RepeatPlayback Next Function MemoryConnection To Stereo System Audio Cable not provided Speaker Mains outletVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionSET Access Main MenuTuner Set Auto Channel SetAfter Scan Completed Screen preset positionsProcedures Is displayed on the screenStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List Channel Islands TV Station Channel Number GuideWinter Hill Clock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Questions And Answers PlaybackConnect the mains power cord TroubleshootingNo power is applied to the recorder Indicator offTimer Recording Won’t stopIndex Front ViewRear View Remote Control How To Use Specifications DA4 Double Azimuth helical