JVC HR-J755EK setup guide Remote Con- trol Functions, SET TV Brand Code, Operate TV

Page 26

26ADVANCEDOPERATIONS (cont.)

Remote Con- trol Functions

SAT

TV Multi-brand Remote Control

Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled.

Before you start . . .

●Turn on the TV using its remote control.

SET TV BRAND CODE

V

VCR

TV/VCR

– –:– –

1 Refer to the chart below. While holding down TV on the recorder's remote control, enter your TV’s brand code using the NUMBER keys, then press STOP.

Check if the TV's power goes off as it should. If it does, try other operations (☞ step 2)

1

2

3

 

 

 

 

2

4

5

6

NUMBER

 

7

8

9

 

 

0

 

4

1

STOP

3

OK

●Once you have set the remote control to operate the TV, you don't have to repeat this step until you replace your remote control's battteries.

●JVC or SAMSUNG has more than one code. If the TV does not function with one code, try entering another.

2

OPERATE TV

 

 

 

First, press TV to set the remote control to TV mode, then

press the corresponding button:

 

 

, TV PROG +/–,

 

TV/VCR, TV +/– (Volume),

 

 

(Muting), NUMBER

 

keys.

 

 

 

●For some brands of TV, you must press OK after having pressed the NUMBER keys.

IMPORTANT

TV PROG+/–

ATTENTION

TV+/–

Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability.

TV BRAND NAME

CODE

 

 

JVC

01, 02, 03, 04

BRANDT

05

The remote control can operate not only the video recorder but also some of your TV and satellite receiver's functions.

●To operate your video recorder, first press the VCR button to set the remote control to the Video mode.

●To operate your TV, first press the TV button to set the remote control to the TV mode.

●To operate your satellite receiver, first press the SAT button to set the remote control to the Satellite Receiver mode.

Control Your TV Using Additional Buttons

Use the NUMBER keys, and the button, button or ä button to select the TV’s channel.

●With televisions under Code 01, 02, 03, 04, 05, 06, 07,

09, 10, 13, 14, 22, 23 or 25, the button corresponds to the 1-digit/2-digit entry switching button (often labelled

– /– –) of your TV’s remote control.

● With televisions under Code 01, 11 or 12, the button corresponds to the 10 + button, and the äbutton corre- sponds to the 20 + button of your TV’s remote control.

NOTE:

The way these buttons are used is determined by your TV. Use these buttons as instructed for your TV’s remote control.

NORDMENDE

05

SABA

05

TELEAVIA

05

TELEFUNKEN

05

THOMSON

05

FERGUSON

06

PHILIPS

07

SAMSUNG

07, 19, 23, 24, 25

BLAUPUNKT

08

GRUNDIG

08

SONY

09

PANASONIC

10

GRAETZ

11

ITT

11

LUXOR

11

SALORA

11

SELECO

11

MIVAR

12

HITACHI

13

TOSHIBA

14

MITSUBISHI

15

FINLUX

16

NOKIA

17

SHARP

18

FUNAI

20

GOLDSTAR

21

NEC

22

Page 25 Page 27
Image 26
Page 25 Page 27
Contents HR-J755EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Mains outlet Back of TVTV Aerial Cable not provided Back of RecorderYour TV via both an RF cable and a 21-pin Go to itemIf auto channel set has succeeded but auto clock set has not Point PlaybackLoad a Cassette Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter Display Remaining TimeVideo Plus+ Timer Programming Timer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Playback Picture Adjustment Skip Over Unwanted Looking For Scene You WantActivate Index Search SectionsActivate Instant Review Instant ReViewS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Soundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Type of Broadcast On-screen Display Being ReceivedActivate Spatializer SpatializerOutdoor Unit Satellite Cable Aerial connectorAutomatic Satellite Programme Recording Satellite Receiver UnitBefore performing the following steps Link SP/LPRemote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverMake Connections Input ModeEdit To Or From Another Video Recorder Start Camcorder SET RECORDER’S Input ModeEdit From a Camcorder Start RecorderENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsReturn to Normal Screen Auto SP→LP TimerAuto Timer Repeat Playback Activate RepeatPlayback Next Function MemoryConnection To Stereo System Audio Cable not provided Speaker Mains outletVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionSET Access Main MenuTuner Set Auto Channel SetAfter Scan Completed Screen preset positionsProcedures Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List Winter Hill TV Station Channel Number GuideChannel Islands Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers PlaybackConnect the mains power cord TroubleshootingNo power is applied to the recorder Indicator offTimer Recording Won’t stopIndex Front ViewRear View Remote Control How To Use Specifications DA4 Double Azimuth helical
Top Page Image Contents