JVC HR-J755EK setup guide Before performing the following steps, Link SP/LP

Page 25

25

LINK

SP/LP

REC

 

ATTENTION

Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

If you have connected another appliance other than a satellite receiver to the AV2 IN connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

Auto Satellite Prog recording and timer-recording cannot be done at the same time.

Before performing the following steps:

Make sure the satellite receiver is connected to the recorder's AV2 IN connector. (pg. 24)

Programme the timer on the satellite receiver.

Insert a cassette with the safety tab in place.

SET TAPE SPEED

1 Press SP/LP () to set the tape speed.

ENGAGE AUTO SATELLITE PROG REC MODE

2 Press and hold REC LINK for about 2 seconds. The button lights up and the recorder turns off automati- cally.

To disengage the Auto Satellite Prog Rec mode, press REC LINK. The light goes off.

If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

NOTES:

Auto Satellite Prog recording is not possible with the AV1 IN/OUT connector.

When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (pg. 19).

For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

The REC LINK button blinks while Auto Satellite Prog recording is in progress.

Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 1 will apply to all the programmes for Auto Satellite Prog recording.

The B.E.S.T. system (pg. 20) does not work while Auto Satellite Prog recording is in progress.

Just Clock (pg. 43) does not work when the Auto Satellite Prog Rec mode is engaged.

Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN connector.

Image 25
Contents HR-J755EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide TV Aerial Cable not provided Back of TVMains outlet Back of RecorderGo to item Your TV via both an RF cable and a 21-pinIf auto channel set has succeeded but auto clock set has not Load a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode Display Remaining TimeVideo Plus+ Timer Programming PDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Playback Picture Adjustment Activate Index Search Looking For Scene You WantSkip Over Unwanted SectionsInstant ReView Activate Instant ReviewTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Receiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection Type of Broadcast On-screen Display Being ReceivedSpatializer Activate SpatializerAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitLink SP/LP Before performing the following stepsControl Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverEdit To Or From Another Video Recorder Input ModeMake Connections Edit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Auto SP→LP TimerReturn to Normal Screen Playback Activate RepeatRepeat Playback Next Function MemoryAudio Cable not provided Speaker Mains outlet Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalTuner Set Access Main MenuSET Auto Channel SetProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterTV Station And ID List Channel Islands TV Station Channel Number GuideWinter Hill Just Clock Clock SetNumber Video Plus+ SetupGuide Program Number Set Playback Questions And AnswersNo power is applied to the recorder TroubleshootingConnect the mains power cord Indicator offWon’t stop Timer RecordingFront View IndexRear View Remote Control How To Use DA4 Double Azimuth helical Specifications