JVC HR-J758EH, HR-DD858EH specifications Recording Features

Page 21

EN21

Recording Features

RECORD

– –:– –

– –:– –

 

TV/VCR

Record One Programme While Watching Another

If your recorder is connected to the TV via AV connection, . . .

. . . press TV/VCR. The recorder's VCR indicator and the TV broadcast being recorded disappear.

SELECT CHANNEL TO

WATCH

1 Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view.

●The programme selected with the TV’s channel controls appears on the TV screen while the one selected with the recorder's TV PROG buttons is recorded on the tape.

●If a decoder is connected to the recorder (☞ pg. 43), you can select a scrambled channel as well with the TV channel controls.

1 2 3

4 5 6

7 8 9

2

Elapsed Recording Time Indication

0000

0

4

TV PROG

You can check the exact time of a recording.

SET COUNTER DISPLAY

1 Press – –:– – until a counter reading appears on the dispay panel.

Instant Timer Recording (ITR)

This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the recorder off after recording is finished.

START RECORDING

1 Press RECORD on the recorder.

ENGAGE ITR MODE

2 Press RECORD again. "" blinks and 0:30 appears on the front display panel.

SET RECORDING DURATION

3 If you want to record for more than 30 minutes, press RECORD to extend the time. Each press extends recording time by 30 minutes.

NOTE:

You can only perform ITR using the RECORD button on the recorder's front panel.

●The HR-J758E/EH owners can use the DISPLAY button on the recorder's front panel as well.

2

 

RESET COUNTER

Press 0000 before starting recording or playback.

 

 

 

● The counter is reset to “0:00:00” and shows the exact

 

elapsed time as the tape runs.

Tape Remaining Time

DISPLAY REMAINING TIME

1 Press – –:– – until the time remaining on the tape appears.

●The display panel shows the tape remaining time with "" displayed.

●By pressing the – –:– – button, you can change the display to show the counter reading, channel position*, clock time or tape remaining time.

*channel position is not displayed during playback.

●The HR-J758E/EH owners can use the DISPLAY button on the recorder's front panel as well.

NOTE:

Depending on the type of tape used, there may be times when the tape remaining time reading may not appear right away, or is not correct. "– –:– –" may sometimes appear, or the display may blink on occasion.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents HR-DD858E/EH HR-J758E/EH Safety Precautions For ItalyDo not place the recorder Basic Connections Check ContentsSituate Recorder Connect Recorder to MainsIf you are referring to the front display panel Auto Set UpIf you are referring to the on-screen display International Telephone Country CodeVia an RF cable only RF connection Language CodeVideo Channel Your TV to the Video Channel. Refer toLanguage for the on-screen display If both auto channel set and auto clock set have failedJust Clock Just Clock onLanguage Access Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysPower Save Mode Select Power Save ModeOK or % About Ntsc Playback Colour System SetOK or% Appears only with HR-DD858E and HR DD858EHLoad a Cassette Basic PlaybackPoint Start PlaybackPlayback Features Activate HIGH-SPEED SearchPause During Playback High-Speed Turbo Search For HR-J758E/EH Still Picture/Frame-By-Frame Playback For HR-J758E/EHSlow Motion For HR-J758E/EH Activate 3R Picture Adjust TrackingOverride Automatic Tracking ManuallySkip Over Unwanted SectionsActivate Instant Review Spatializer Activate SpatializerSoundtrack Selection During PlaybackRepeat Playback TimeScan Audio signal during TimeScanVariable-Speed Search HR-DD858E/EH only Press Pause Press TV Prog + or so that the vibration stopsTimeScan Audio TimeScanSpeed SP Speed LP Audio output HR-DD858EHR-DD858EHBasic Recording Recording Features Receiving Stereo Bilingual Programmes To Record Stereo And Bilingual Programmes A2Type of Broadcast On-screen Display Being Received Hi-Fi Audio Recording Level Control HR-DD858E/EH only Adjust AudioSelect B.E.S.T. Mode S.T. Picture SystemPreparation Playback RecordingOr press Record on the recorder During B.E.S.TTimer Programming Satellite Tuner Users Timer WarningStart Time Express Timer ProgrammingEnter Programme Stop TimeTimer Mode SET VPS/PDC ModeEngage RECORDER’S VPS/PDC RecordingPress Check, Cancel And Replace ProgrammesPress Again to check More information. Each Time you pressAuto SP→LP Timer Auto TimerFor Example Prog REC Mode Automatic Satellite Programme RecordingBefore performing the following steps Remove Power Supply Remote Control FunctionsSET Remote Control Code RE-SUPPLY PowerSET TV Brand Code TV/VCR, TV +/- VolumeOperate TV TV Prog +Operate Satellite Tuner Satellite Tuner Multi-Brand Remote ControlBefore you start Satellite Tuner Brand CodeEdit To Or From Another Video Recorder SET Recording DECK’S Input ModeMake Connections Start Source PlayerAV2 Select Setting Edit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderLocate Start Point SET Input ModeEngage Audio Dubbing Start DubbingInsert Editing Reset the CounterLocate END Point ProgEngage Insert Editing Start EditingEND Insert Editing Connection To Satellite Tuner Satellite Tuner UnitBack of Recorder Select Input Mode Connecting Using a DecoderConnect Decoder SET TunerAUX in or Tape Monitor Connecting Using a Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelAuto Channel Set Tuner SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Delete a ChannelChange Station Channel Position Switch Stations Access ManualChannel SET Screen Select NEW StationStation Name TV Station And ID ListFine-Tuning Channels Already Stored Perform TuningSelect Channel to FINE-TUNE Press OK twice. The Manual Channel Set screen appearsNumber Showview SetupEnter Receiving Channel Position Number Guide Program Number SetAccess Clock SET Screen Access Initial SET ScreenClock Set SET Date and TimeSET Just Clock SET Clock Data Source Channel PositionStart Clock Operation Remote control wont function No power is applied to the recorderMains power cord is discon- nected If you’re using the RF OUT connec- tionTimer Recording Ä remain lit on the display panel. Is there Problem? EN Questions and AnswersIndex HR-DD858E/EH only EN IndexRemote Control Maximum recording time IN/OUT x 1, IN/DECODER xFrequency synthesized tuner Memo Ex. Francais is selected for Belgium International Telephone Language CodeFor More Information see INSTRUCTIONS/P4
Top Page Image Contents