JVC HR-S9911U Other Functions, Timer warning display, Checking tape position, Function settings

Page 19

C Select tape number

Press rt to move the highlight bar (arrow) to the tape number on which you want to record a program, then press OK. The calculated blank space is based on

the current tape speed (SP or EP) selected on the VCR.

If the selected cassette has already been loaded, the VCR searches the beginning of the blank space and goes into the stop mode automatically.

DLoad cassette

Insert the tape of the selected number.

The VCR searches the beginning of the blank space and goes into the stop mode automatically.

Other Functions

Timer warning display

A warning appears on the TV screen to tell you that the timer-recording is to start in 5 minutes if you are not in the timer

recording standby mode at that time. Press TIMER (#) to put the VCR into timer

recording standby mode. To clear the display, press CANCEL on the Remote.

Checking tape position

When you change the VCR operation mode from the stop mode to fast forward

or rewind mode, or when you perform an Index Search ( pg. 11) or Instant Review ( pg. 12), the tape position indicator appears.

The position of “q” in relation to “B” (Beginning) or “E” (End) shows you where you are on the tape.

Set “SUPERIMPOSE” to “ON” ( pg. 20).

Function settings

You can use the other useful function settings on the Function Set screen.

Turn on the VCR and TV, and select the VCR channel (or AV mode).

Set the VCR/TV/CABLE/DBS selector on the Remote to “VCR”.

A Access Main Menu screen, then

Function Set screen

Press MENU on the Remote. Press rt to move the highlight bar (arrow) to “FUNCTION SET”, then press OK or e.

BSelect Function

Press rt to move the highlight bar (arrow) to the function you want to set.

CChange setting

Press OK or e. The default setting is bold in the table below. Press MENU to return to normal screen.

After a power failure occurs, Function Settings will be reset to its default setting.

S-VHS ET — ON/OFF

When this function is set to “ON”, you can record on VHS cassettes with S-VHS picture quality. Tapes recorded using this function can be played back on most of S-VHS VCRs or VHS VCRs equipped with the SQPB (S-VHS QUASI PLAYBACK) function. When this function is set to “ON”, the S-VHS indicator lights up on the display panel.

Changing display information

Each time you press DISPLAY, the display panel shows the time counter, the channel number, the clock time and the tape remaining time alternatively.

To reset the time counter, press C.RESET on the Remote.

During playback, the channel number is not shown.

When the tape remaining time appears, “z” also lights on the display panel.

When “SUPERIMPOSE” is set to “ON”

( pg. 20) and DISPLAY on the Remote is pressed, the current VCR status appear on the TV screen.

NOTES:

Before recording, set “VIDEO CALIBRATION” to “ON”.

( See below)

You cannot activate the S-VHS ET function while recording, timer-recording or Instant Timer Recording ( pg. 13) or the “VIDEO CALIBRATION” function ( See below) is in progress.

The S-VHS ET function does not work with S-VHS cassettes. To keep the highest quality recording and playback pictures

over a long period of time, S-VHS recording on S-VHS cassettes is recommended.

Use of high grade tapes is recommended for S-VHS ET recordings. On some tapes, picture quality will not improve even if the S-VHS ET function is used. Check the recording quality before you start important recordings.

VIDEO CALIBRATION ON/OFF

When this function is set to “ON”, this VCR checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible pictures. This takes place whenever you play back a tape or start recording after inserting a tape.

NOTE:

The VCR checks the tape condition for about 7 seconds, then starts recording. To make sure you record the desired scene or program completely, perform the following steps:

APress and hold PAUSE (9), and press REC (7). After about 7 seconds, the VCR re-enters Record Pause mode.

BPress PLAY (4) to start recording.

CONTINUED ON NEXT PAGE

— 19 —

Image 19
Contents HR-S9911U Declaration of Conformity Video heads cleaning How to use the RemoteFront Panel IndexRear Panel Display Panel Remote On-Screen DisplayTo recall an indication AV Connection Connections and Plug&Play SettingVideo Connection RF ConnectionLanguage Setting Initial SettingsClock Setting Setting channels manually Manual Channel Set Tuner SettingCable Box and/or DBS Receiver Control Setting Setting channels automatically Auto Channel SetBasic Playback PlaybackOn the Remote On the VCRPlayback Features Basic Recording Locating beginning of timer recordings Instant ReviewAdjusting picture condition Digital TBC/NR RecordingRecording Features Changing VCR Plus+ Setting Timer RecordingVCR Plus+ Timer Programing To use the VCR while it is in timer recording standby mode Express Timer Programing24HR Quick Programing Video Navigation Title Screen Program overlap warning displayDeactivating Video Navigation Deleting tape information Editing TitlesEditing tape title Editing program title and categoryFinding Titles Checking tape position Timer warning displayFunction settings Other FunctionsWhen this function is set to OFF When this function is set to onChild Lock Jlip ID Number SettingAccess Jlip ID Number Set screen Satellite Auto RecordingCable Box or DBS Receiver Brand Setting Multi-Brand Remote ControlChanging Remote Control Code TV Brand SettingEditing from Camcorder EditingSelect input location on recording VCR Select video input connector on recording VCRExample 1 When another VCR is VHS VCR Editing with Another VCRStart dubbing Audio DubbingInsert Editing and AV Dubbing Select input locationStart editing SpecificationsLocate start point, and engage Insert Editing mode Locate end pointPlayback TroubleshootingPower Timer RecordingVideo Navigation Other ProblemsFor Servicing Only in U.S.A HOW to Locate Your JVC Service CenterLimited Warrantyconsumer Video Warranty Only in U.S.AMemo