Editing from Camcorder

CChange code for VCR

Press any key on the Remote. The VCR now responds to B code control signals.

●To set the Remote and the VCR to transmit and respond to A code control signals, repeat above procedure as shown above except press the Number key “1” in step B of 1.

To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control code for the Remote between A and B ( step A), keeping two VCRs to different control codes.

●To change only the remote control code for the Remote, DO NOT perform steps B and C.

Editing

Various connection for editing tapes

The following three methods can be used for editing tapes.

●VHS to S-VHS editing (VIDEO-VIDEO connection): Although the picture quality is inherently limited by the original VHS quality, the edited tape has better picture quality than those made by VHS-to-VHS editing.

●S-VHS to VHS editing (VIDEO-VIDEO connection):

Since the original source is recorded in S-VHS mode, the edited tape has better picture quality than those made by VHS-to-VHS editing.

●S-VHS to S-VHS (S-VIDEO connection):

Original picture quality of S-VHS made can be duplicated with minimal picture degradation. This is the best editing method you can use on S-VHS VCRs.

You can use a camcorder as the playback unit and your VCR as the recording VCR. Refer also to the camcorder’s instruction manual for connection and its operations.

AMake connections

This VCR (for recording)

To AUDIO/VIDEOTo S-VIDEO input input

		To rear panel
		REMOTE PAUSE/
		AV COMPULINK
	Audio/video cable	S-video cable
	(supplied)	(supplied)
	To audio/video	To S-video output
	output
		To EDIT
	Camcorder	Mini-plug cable
	(for playback)	Mini-plug cable
	(for playback)	(not supplied)
		(not supplied)
		(JVC camcorder only)

●When the JVC camcorder is equipped with the Master Edit Control, you can control the VCR from the camcorder. Connect the mini-plug cable (not supplied with this VCR) as illustrated.

●If camcorder is monaural, connect the audio output connector on the camcorder to the left audio input connector on this VCR.

BLoad cassettes

Insert the playback cassette into the camcorder and the cassette to be recorded on into this VCR.

CSelect input location on this VCR

Select the correct external input location on this VCR.

Select “L-1” —when connecting the camcorder to the audio/video (or S-video) input connectors on the rear panel.

Select “F-1” —when connecting the camcorder to the audio/video (or S-video) input connectors on the front panel.

On the VCR

Press CH+/– or push the ADVANCED JOG dial, then turn it to the left or right until “L-1” or “F-1” appears on the display panel.

On the Remote

Press AUX and/or CH+/– until “L-1” or “F-1” appears on the display panel.

DSelect video input connector

Select the appropriate mode depending on the connector being used ( pg. 21).

When using S-VIDEO input connector on the front panel, set “FRONT AUX INPUT” to “S-VIDEO”.

When using S-VIDEO IN connector on the rear panel, set “REAR AUX INPUT” to “S-VIDEO”.

When using VIDEO input connector on the front panel, set “FRONT AUX INPUT” to “VIDEO”.

When using VIDEO IN connector on the rear panel, set “REAR AUX INPUT” to “VIDEO”.

ESelect edit mode

Set “PICTURE CONTROL” to “EDIT” ( pg. 20).

FSet AV COMPU-LINK mode

If your JVC camcorder is equipped with a Master Edit Control, set “AV COMPU-LINK” to “OFF” ( pg. 21). The REMOTE PAUSE/ AV COMPULINK connector works as a Remote Pause connector.

GStart playback

Set the camcorder to its play mode.

NOTE:

If the camcorder is equipped with a superimpose/OSD disable feature, set it to “OFF” before starting playback.

HStart recording

On the VCR

Press REC (7).

On the Remote

While holding REC (7), press PLAY (4).

●If you are using a Master Edit Control-equipped JVC camcorder, recording starts automatically on this VCR. (Refer to camcorder’s instruction manual.)

NOTE:

Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish dubbing the tapes. ( pg. 20)

— 23 —