Audio Dubbing
Audio Dubbing replaces a previously recorded normal audio track with a new soundtrack.
AMake connections
Connect an audio cable between the VCR’s audio input connectors and the audio component’s audio output connectors.
●When connecting a monaural audio component, use only the VCR’s AUDIO L input connector.
●Audio Dubbing is possible only by using the audio input connectors on the front panel or on the rear panel.
This VCR
To AUDIO input 
To audio output
CD player, etc.
BSelect input location
Select
Select
On the VCR
Press CH+/– or push the ADVANCED JOG dial, then turn it to the left or right until
On the Remote
Press AUX and/or CH+/– until
CLocate start point, and engage Audio Dubbing mode
Load a cassette and press PLAY (4) on the VCR. Press PAUSE (9) at the point where you want to start dubbing, then press A.DUB.
●The VCR enters the Audio Dubbing Pause mode. “o” blinks, “u” and “i“ light up on the display panel.
DStart dubbing
Engage the Play mode on the audio component, then press PLAY (4) on the VCR. Audio Dubbing begins. “o” blinks, and “u” lights up on the display panel.
●To pause dubbing, press PAUSE (9). Press PLAY (4) to resume dubbing.
EEnd Audio Dubbing
Press STOP (8) on the Remote or STOP/EJECT (0) on the VCR, then engage the Stop mode of the audio component.
NOTES:
●When monitoring the sound during Audio Dubbing, the normal soundtrack is automatically selected. If you wish to hear the
●Audio Dubbing stops automatically when the counter reaches “0:00:00”, and the VCR enters the Play mode. Check the counter reading before dubbing.
●Audio Dubbing is not possible with a cassette whose record safety tab has been removed.
●When playing back an
Insert Editing and AV Dubbing
Insert Editing:
You can replace a recorded scene with new scene recorded on another tape or with other material. Both the picture and the sound recorded on the
AV Dubbing:
You can perform Audio Dubbing and Insert Editing at the same time. This means that the picture and the sounds recorded on the
●For AV Dubbing, you can edit pictures and sound using different sources; connect a video source to the video input connector, and an audio source to the audio input connectors.
AMake connections
Connect the supplied audio/video cable between the VCR’s audio/ video input connectors and the other component’s audio/video output connectors.
●Insert Editing and AV Dubbing are possible only by using the audio/video input connectors on the front panel or on the rear panel.
|
| This VCR (for recording) | ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To AUDIO/VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
|
| To | |
| input |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Audio/video cable | |
(supplied) | (supplied) |
To audio/video output 
To
Another VCR (for playback)
BSelect input location
Select
Select
On the VCR
Press CH+/– or push the ADVANCED JOG dial, then turn it to the left or right until
On the Remote
Press AUX and/or CH+/– until
CSelect video input connector
Select the appropriate mode depending on the connector being used ( pg. 21).
When using
When using
When using VIDEO input connector on the front panel, set “FRONT AUX INPUT” to “VIDEO”.
When using VIDEO IN connector on the rear panel, set “REAR AUX INPUT” to “VIDEO”.
DSelect edit mode
Set the edit mode to “ON” for the VCRs if such a mode is equipped.
●On this VCR, set “PICTURE CONTROL” to “EDIT” ( pg. 20).
CONTINUED ON NEXT PAGE
— 25 —