JVC HR-S9500U manual Commercial Advance works as follows

Page 32
MARKING COMMERCIALS

32EN

PLAYBACKANDRECORDINGFEATURES(cont.)

Commercial Advance

Your VCR is eqipped with the Commercial Advance feature, which can automatically fast-motion the tape during playback to skip over previously recorded TV commercials.

Commercial Advance works as follows:

1When recording is finished, the following display will appear on the screen and the VCR's front display panel.

MARKING COMMERCIALS WILL BE EXECUTED.

PRESS (OK) TO START PRESS (STOP) TO CANCEL

NOTE:

*In case of timer recording, these displays will appear when all the preset programs are recorded. If you press TIMER to disengage the timer mode, these displays will appear even if all the programs are not recorded yet.

a– Press OK and step 2 will take place.

b– If you do not want to use Commercial Advance for the recorded program, press STOP.

c– If neither button is pressed within 60 seconds after the displays appear, step 2 will take place automatically.

IMPORTANT

If you press STOP in this step or stop marking midway in step

2 before the VCR is finished marking the commercials, data

necessary for Commercial Advance will be lost and this feature

Commercials can only be marked if Commercial Advance Record is enabled (☞ pg. 33).

will not work with the recording you made.

2The VCR rewinds the tape automatically to the beginning of the recording and seeks out the commercial groups which have been detected.

During search and marking

Search and marking

Program

Commercial Commercial Commercial

Program

*If you want to stop marking midway, press STOP so that "MARKING IN PROCESS" appears on the screen and "CA" blinks on the front display panel. While those are displayed (for 5 seconds), press STOP again to cancel

Commercial Advance marking of the rest of the recordings.

*If you want to watch a TV program while the VCR is marking commercials, first press TV/VCR on the remote control, then use the TV's channel selector to select the channel you want to watch.

 

 

Commercial group

 

 

MARK

MARK

After having marked the start and end of all commercial groups of the recording(s), the VCR goes to its Stop mode. In the case of timer recording or Instant Timer Recording, the VCR shuts off automatically.

3During playback, the VCR automatically (when enabled ☞ pg. 33) fast-motions (with blueback screen) (☞ pg. 38) during the commercial groups that were marked in step 2.

* When Commercial Advance is forwarding the tape to skip over commercials, "CA SKIP" will be displayed in the top right corner of the TV screen.

 

 

 

 

Forward fast-motion playback

 

 

 

 

 

 

Playback

 

(with blueback screen)

 

 

 

Playback

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Program

 

Commercial

Commercial

Commercial

Program

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Commercial group

 

 

 

 

 

 

 

 

MARK

 

MARK

 

 

 

 

 

NOTES:

●The Commercial Advance Record processes marks the tape when the picture fades to black and the audio fades to silence. Normally there is a period of black and no audio at the beginning and end of commercials.

●A black screen or a scene with no audio signal during a program may be detected as the start or end of a commercial.

●When using the timer to record two adjacent shows on the same channel, better commercial detection accuracy can be obtained by programming each show separately.

●If you record over a commercial start or end mark the Commercial Advance feature will not work correctly.

●Commercial Advance tested with 6 hours recordings, longer recordings may be possible depending on the number of commercials contained in the broadcast.

●The VCR will resume normal playback after skipping 15 minutes of tape if no commercial group end mark is detected.

●If the end of the tape is reached during recording, the display as illustrated in step 1 appears, then...

•in the case of timer recording or Instant Timer Recording, after step 2 takes place, the cassette will be ejected and the power will shut off.

•in the case of normal recording, after step 2 takes place, the VCR will rewind to the beginning of the tape.

●During automatic commercial skipping, if the user presses STOP or PLAY, the VCR will resume normal play; furthermore, if the tape is reversed to before the commercial group and played, the commercial group will not automatically be skipped.

●If an index code or the end of a recording is detected during Commercial Advance's forward fast-motion playback, normal playback resumes automatically.

●Commercial Advance disables commercial marking when the recording is less than 15 minutes.

●Commercial Advance does not mark the start of a commercial group when it is in the first or last two minutes of a recording.

●Commercial Advance does not mark commercial groups which are less than 59 seconds or groups which contain only one commercial.

●Some portions of programs may be detected as commercials.

●Some commercials may not be detected properly.

Page 31 Page 33
Image 32
Page 31 Page 33
Contents HR-S9500U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsServicing Before YOU Install Your NEW VCRUSE Contents Connections AC Power Cord Back of VCRMatching Transformer not supplied Connect VCR to TVPlug & Play Setup Plug & PlayEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetInformation Language Access Clock SET ClockPreparation ScanSelect D.S.T. Mode SET Auto Clock to onSelect Host Channel Semi-AutoSelect Time Zone Return to Normal ScreenSET Time SET DateAccess Main Menu Screen Access Tuner SET ScreenTuner SETAccess Manual ChannelAdd Or Delete a Channel Time Scan %Cable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Turn on Cable BOXSelect Cable BOX Output ChannelAccess Cable BOX Brand SET Screen Initial SettingsEnter Cable BOX Brand Brand CodeDBS Receiver Control Connect DBS Receiver To VCRYour VCR Controller DBS receiverAccess DBS Receiver SET Turn on DBS ReceiverSelect DBS Receiver Set DBS Receiver Output Channel & DBS Receiver BrandAccess DBS Receiver SET DBS Receiver BrandSimple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Playback Features Activate FRAME-BYFrame Playback Still Picture/Frame-By-Frame PlaybackActivate HIGH-SPEED Search Pause During PlaybackEngage Manual Tracking Mode Adjust Manual TrackingLayback and Recording Features RE-ENGAGE Automatic TrackingAccess Distant Code Start SearchStart Repeat Stop RepeatVideo Stabilizer Activate Video StabilizerCH 5 or Time Scan Time SCAN%to set to Select Superimpose SET Mode Superimpose Access Function SET SET ModeSelect Audio Monitor Select The SoundtrackPerform Movie Advance Commercial Advance Commercial Advance works as followsReturn to Normal Screen Access Main Menu ScreenSelect CA Playback SET Mode Example AV Compu Link PlaybackMake Connection Select Digital R3 SET Digital TBC/NRDigital R3 Select Video Calibration ModeActive Video Calibration Recording Start PlaybackAudio signal during TimeScan TimeScanVariable-Speed Search/ Reverse Motion Playback Activate VARIABLE-SPEEDTimeScan TimeScan AudioSpeed Audio output Pro-SlowRecording Features VHS Super VHS, S-VHS ET and VHS Super VHS ET Select S-VHS ET SET ModeEngage S-VHS ET Mode To Record SAP Programs Select 2ND Audio Record SET ModeStereo And SAP Second Audio Program Adjust Audio Select ModeControl Screen Recording LevelInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC on the front panelVCR Plus+ Timer Programming EN Timer RecordingNumber Enter Pluscode NumberEngage Timer Mode OK or Time SCAN% VCR Plus+ SetupVCR Plus+ Guide Channel Matching Access Guide Channel SET Screen Input Guide Channel NumberInput Receiving Channel Number Scan %SET Channel Number Express Timer ProgrammingSET Program Date Set to OFF pg , Band indication TV or CatvOr DBS appears under Channel number display. IfCancel or Revise a RE-ENGAGE TimerCheck, Cancel And Revise Programs ProgramSelect Auto SP→EP Timer SET Mode Auto SP→EP TimerAuto Timer Select Auto Timer SETEdit From a Camcorder VideoEnable Remote Pause Function Access Function SET ScreenStart Player Start RecorderEdit To Or From Another SET Input Mode Locate Start PointEngage Audio Dubbing Start DubbingReset the Counter Insert EditingLocate END Point Another VCR PlayerEND Insert Editing Engage Insert EditingStart Editing SET Remote Control Mode Turn on the TVSET TV Brand Code Operate TVCable Box Multi-Brand Remote Control Turn on the Cable BOXOperate Cable BOX Cable BOX Brand Name Brand CodeSET Remote Control Special FeaturesDBS Receiver Multi-Brand Remote Control Turn on the DBSTurn VCR Power on Unplug Vcrs PowerPlug in Power Cord Engage Child LockAccess Jlip ID NO. SET Terminal JLIPJoint Level Interface Protocol ConnectorSET Jlip ID Number Terminal Back of VCRMake sure the cassettes window is Troubleshoo Ting E NCassette gets stuck partway Timer again OubleshootingOther Problems When scanning channels, someEN Questions and Answers Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording?Express Timer Programming MBR Multi-Brand Remote Code SettingIndex List Of TermsFront View Rear View Remote Control EN IndexSpecification S Video connectors in x 2, OUT x20C to 60C -4F to140F Maximum recording timeHOW to Locate Your JVC Service Center For ServicingWarranty Limited WarrantyHR-S9500U
Top Page Image Contents