JVC HR-S6600EK setup guide With RF Connection

Page 41

STOP

41

With RF Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■the connected TV is turned on.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

1 Press and hold down STOP on the recorder until the display panel shows the following.

1 2 3

4 5 6

7 8 9

0

1

?

2

4

TV PROG

OK

SET VIDEO CHANNEL

2 Press TV PROG+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 48 for details of broadcast stations in your area.

(Ex.) If channel 36 is available in your area

Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.)

●If the two vertical white bars appear clearly on the screen as shown in the illustration at buttom left, go to step 3.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

IMPORTANT

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

TEST SIGNAL

The channel on which the screen on the left appears clearly in step 2 is your Video Channel.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 41

Contents HR-S6600EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Connect Video Recorder to TVBack of TV Video Connection Back of TV Audio in connectorsGo to item Before performing the following procedure, make sure thatShows either the display as illustrated on Or remote control until the display panelProgress, this process will be interrupted You will need to start again. See Notes belowIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notLink Functions TV Auto Power OnTurn on the Recorder NexTView LinkLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search PlaybackSearch Recording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingStart Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenAccess Programme SCREEN/ Display Check, Cancel And Replace ProgrammesCancel or Replace a Programme Return to Timer ModeVHS Super VHS and VHS Recording According To Tape TypeAccess Mode SET Screen Access Main Menu ScreenPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemOr press Record on the recorder RecordingPlayback Adjust Tracking Manually Playback Picture AdjustmentManual Tracking Override Automatic TrackingSkip Over Unwanted Looking For Scene You WantSections Activate Index SearchSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackMinimizing Picture Degradation While Editing Select Picture Control SET ModeReturn to Normal Screen Advantages Of S-VHS Video RecordersSET Edit Mode SET RECORDER’S Input ModeEdit From Camcorder Make ConnectionsEdit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV2 Select Setting AV1 Select SettingTV Aerial cable Connector Audio in connectors ConnectorAutomatic Satellite Programme Recording Satellite Receiver UnitAccess Main Menu Screen Other Functions ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Display 13 14Power SAVE, then press Power Save ModeSelect Power Save Next Function Memory Auto TimerRepeat Playback Auto SP→LP TimerNtsc Playback Activate Repeat PlaybackAudio Cable not provided Speaker Connection To Stereo SystemJust Clock Clock SetExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Switch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Guide Program Number Set Video Plus+ SetupNumber Troubleshooting Won’t stop Timer RecordingÄ remain lit on the display panel. Is there Problem? Questions And AnswersFront View IndexRear View # $ Display PanelButton accesses Program screens/displays Remote ControlVCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoEMO Memo VHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical