JVC HR-S6600EK setup guide Troubleshooting

Page 50

50

SUBSIDIARY INFORMATION

Troubleshooting

Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair.

POWER

SYMPTOM

1.No power is applied to the recorder.

2.The clock is functioning properly, but the recorder cannot be powered.

3.The remote control won’t function.

TAPE TRANSPORT

SYMPTOM

1.The tape does not run during recording.

2.The tape will not rewind or fast- forward.

PLAYBACK

SYMPTOM

1.The playback picture does not appear while the tape is running.

2.Noise appears during visual search.

3.Noise appears during normal playback.

4.The playback picture is blurred or interrupted while TV broadcasts are clear.

5.Breaks are noticeable in Hi-Fi soundtrack.

RECORDING

SYMPTOM

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

POSSIBLE CAUSE

The mains power cord is disconnected.

“ä“ is displayed on the display panel with Auto Timer set to "OFF".

The batteries are discharged.

POSSIBLE CAUSE

“ is displayed on the display panel.

The tape is already fully rewound or fast-forwarded.

POSSIBLE CAUSE

If you’re using the RF OUT connec- tion . . .

. . . the TV receiver’s channel selector is not set to the VIDEO channel.

. . . the recorder's VIDEO channel has not been correctly set.

If you’re using the AV or S-VIDEO connection, the TV receiver is not set to the AV mode.

This is normal.

The automatic tracking mode is engaged.

The video heads may be dirty.

Automatic tracking is engaged.

POSSIBLE CAUSE

There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed.

“L-1”, “L-2” or “S-1” has been selected as the input mode.

The source (another video recorder, camcorder) has not been properly connected.

All necessary power switches have not been turned on.

The input mode is not correct.

CORRECTIVE ACTION

Connect the mains power cord.

Press the äbutton to turn the “ä“ indicator off.

Replace the dead batteries with new ones.

CORRECTIVE ACTION

Press PLAY to turn the ““ indicator off.

Check the cassette.

CORRECTIVE ACTION

If you are using the RF OUT connec- tion . . .

. . . set the TV receiver to the VIDEO channel. (pg. 8)

. . . Perform "Video Channel Set" (pg. 40)

If you are using the AV or S-VIDEO connection, set the TV to its AV mode.

Try manual tracking (pg. 24).

Consult your JVC dealer.

Engage and adjust tracking manually (pg. 24) or press AUDIO to change the soundtrack to "NORM" (pg. 26).

CORRECTIVE ACTION

Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.

Set to the desired preset.

Confirm that the source is properly connected.

Confirm that all units’ power switches are turned on.

Set the input mode to “L-1”,“L-2” or “S-1”.

Image 50
Contents HR-S6600EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder Connect Video Recorder to TVBack of TV Back of TV Audio in connectors Video ConnectionBefore performing the following procedure, make sure that Go to itemProgress, this process will be interrupted Or remote control until the display panelShows either the display as illustrated on You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTurn on the Recorder TV Auto Power OnLink Functions NexTView LinkPoint PlaybackLoad a Cassette Start PlaybackActivate HIGH-SPEED Search PlaybackSearch Recording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingStart Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCancel or Replace a Programme Check, Cancel And Replace ProgrammesAccess Programme SCREEN/ Display Return to Timer ModeRecording According To Tape Type VHS Super VHS and VHSPlayback/ Recording According To Tape Charac- teristics Access Main Menu ScreenAccess Mode SET Screen S.T. Picture SystemOr press Record on the recorder RecordingPlayback Manual Tracking Playback Picture AdjustmentAdjust Tracking Manually Override Automatic TrackingSections Looking For Scene You WantSkip Over Unwanted Activate Index SearchReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackReturn to Normal Screen Select Picture Control SET ModeMinimizing Picture Degradation While Editing Advantages Of S-VHS Video RecordersEdit From Camcorder SET RECORDER’S Input ModeSET Edit Mode Make ConnectionsEdit To Or From Another Video Recorder TV Receiver Player Your recorder Recorder AV1 Select Setting AV2 Select SettingAutomatic Satellite Programme Recording ConnectorTV Aerial cable Connector Audio in connectors Satellite Receiver UnitAccess Main Menu Screen On-Screen Display ENABLE/DISABLE ON-SCREEN DisplayOther Functions 13 14Power SAVE, then press Power Save ModeSelect Power Save Auto Timer Next Function MemoryNtsc Playback Auto SP→LP TimerRepeat Playback Activate Repeat PlaybackConnection To Stereo System Audio Cable not provided SpeakerClock Set Just ClockVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET After Scan Completed Screen preset positionsProcedures Is displayed on the screenInput Channel Select BandStoring Channels Manually Enter NEW Channel InformationDelete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Channel SET Screen Access ManualSwitch Stations Select NEW StationTV Station And ID List TV Station Channel Number Guide Guide Program Number Set Video Plus+ SetupNumber Troubleshooting Timer Recording Won’t stopQuestions And Answers Ä remain lit on the display panel. Is there Problem?Index Front ViewRear View Display Panel # $Remote Control Button accesses Program screens/displaysAuto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingEMO Memo VHF 44.5 143/143 470 MHz Maximum recording timeDA4 Double Azimuth helical