
LOCATE EDIT-IN POINT
53
END R.A. EDIT |
7
Find the point on the source tape from where you want the edited scene to begin by pressing SEARCH TY, or using JOG dial/SHUTTLE ring, then press SELECT (IN/OUT).
|
|
| R.A. EDIT | EDIT MODE | |
= | 1 |
|
| ||
|
| 2 |
|
| |
|
|
| |||
3 |
|
| |||
4 |
|
| |||
5 |
|
| |||
6 |
|
| |||
7 |
|
| |||
8 |
|
| |||
|
|
| TTL 0:00:00 | CNT 0:00:00 |
11 | Press MENU as many times as necessary to return to the |
normal screen, and engage the Stop mode for the both | |
VCRs. |
NOTES:
● You can also monitor the sound when searching for scenes
8
●To use the remote
control's JOG dial or SHUTTLE ring, press JOG/ SHUTTLE first so that the button lights. Pressing the button again turns off the light.
●The
●You can also perform an Index Search (if index marks have been previously recorded on the tape at the desired points ☞ pg. 31) to find the points you want, but this will result in reduced accuracy.
LOCATE EDIT-OUT POINT
Find the point where you |
|
|
|
| R.A. EDIT | EDIT MODE | ||
want the edited scene to |
|
|
|
|
| |||
|
| = | 1 | 0:02:23 |
| |||
|
|
| ||||||
end by pressing SEARCH |
|
|
| 2 |
|
| ||
|
|
| ||||||
TY, or using JOG | 3 |
|
| |||||
4 |
|
| ||||||
dial/SHUTTLE ring, then | 5 |
|
| |||||
press SELECT (IN/OUT). | 6 |
|
| |||||
|
| 7 |
|
| ||||
● To use the remote | 8 |
|
| |||||
|
|
|
| TTL 0:00:00 | CNT 0:02:23 | |||
control's JOG dial or |
|
|
|
|
|
|
| |
SHUTTLE ring, press |
|
|
|
| R.A. EDIT | EDIT MODE | ||
JOG/SHUTTLE first so |
|
| 1 | 0:02:23 | 0:02:51 | |||
| ||||||||
|
|
| = | 2 |
|
| ||
that the button lights. |
|
|
| |||||
|
|
| 3 |
|
| |||
Pressing the button again |
|
|
|
| ||||
4 |
|
| ||||||
turns off the light. | 5 |
|
| |||||
● The | 6 |
|
| |||||
7 |
|
| ||||||
registered in memory and | 8 |
|
| |||||
appears on the screen. |
|
|
|
| TTL 0:00:28 | CNT 0:02:51 |
● The total time of the |
edited scenes is displayed to the right of "TTL". |
● Repeat steps 7 and 8 for each additional scene. |
you want to edit in steps 7 – 8. Since you can hear the soundtrack during selection, you can avoid abrupt or unnatural sounding
● When editing, there may be a discrepancy of about 2 seconds on the source tape between the locations you chose as
● There are no limitations for R.A. Edit list (such as repeat segments, negative counter values, segments out of order). Only the
● For any scene, the
● Since the source VCR prerolls during Random Assemble Editing, there must be at least 15 seconds worth of recorded material prior to any
● If the search time for an
To Make Corrections . . .
. . . during step 7 or 8, you can cancel registered in and out points by pressing CANCEL on the remote control. Each time you press, the preceding point is erased.
● If, for example, you have registered 5 sets of in and out points and want to reset the first set, you have to press CANCEL until all points after the first set have been erased. Reenter them after you've repaired the first set of points.
9
PREPARE RECORDING DECK
Engage its
START R.A. EDIT
Memory Capacity
Random Assemble Editing shares memory space with the VCR's timer. If there are programs occupied by
R.A. EDIT | EDIT MODE |
PROGRAM FULL | |
TTL 0:00:00 | CNT 0:00:00 |
10
Press R.A. EDIT START on the VCR or START on the remote control.
●Automatic editing begins; all the specified scenes are copied to the recording deck in the order they were registered.
●The
●During scene search, the recording deck automati- cally enters its
●When all registered scenes have been edited, your VCR enters the Still mode, the recording deck enters its
●When all 8 programs are full, "PROGRAM FULL" appears on the R.A. EDIT screen.
●To cancel a program, see page 44.
RM-V403U Multi-Brand R.A. Edit Controller (Not supplied)
By connecting this controller to your VCR's R.A. EDIT connec- tor, you can perform Random Assemble Editing in combination with a second