JVC HR-S7950EU Next Function Memory, Repeat Playback, Manual Tracking, Soundtrack Selection

Page 23

EN 23

Next Function Memory

The Next Function Memory “tells” the recorder what to do after rewinding. Before continuing, make sure the recorder is in the Stop mode.

a- For Automatic Start Of Playback

Press 3, then press 4 within 2 seconds. b- For Automatic Power Off

Press 3, then press 1 within 2 seconds. c- For Automatic Timer Standby

Press 3, then press # (TIMER) within 2 seconds.

NOTE:

The Automatic Power Off does not work if “AUTO TIMER” is set to “ON” ( 49) and if any timer programming has been made. If “AUTO TIMER” is set to “ON”, the recorder directly goes into the Timer-Standby mode at the same time when the 1 is pressed for the Automatic Power Off.

Repeat Playback

Your recorder can automatically play back the whole tape 100 times repeatedly.

1Start playback.

Press 4.

2Activate Repeat Playback.

Press 4 and hold for over 5 seconds, then release.

●The Play indicator ($) on the front display panel blinks slowly.

●After playing back a tape 100 times, the recorder stops automatically.

3Stop Repeat Playback.

Press 8 at any time.

●Pressing 4, 3, 5 or 9 also stops Repeat Playback.

NOTE:

Repeat playback is not possible with a cassette recorded in EP mode.

Manual Tracking

Your recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the PR buttons.

1Override automatic tracking.

During playback, press p on the remote control.

2Adjust the tracking manually.

Press PR + or – on the remote control.

●Press p again to return to automatic tracking.

NOTE:

When a new tape is inserted, the recorder enters the automatic tracking mode automatically.

Soundtrack Selection

Your recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.

During Playback

Pressing AUDIO changes the soundtrack as follows:

TRACK

USE

 

On-Screen Display

 

 

 

HI FI

For Hi-Fi stereo tapes

L j h R

 

 

 

HI FI

For main audio of Bilingual tapes

L j

 

 

 

HI FI

For sub audio of Bilingual tapes

h R

 

 

 

NORM

For audio-dubbed tapes

 

 

HI FI

For audio-dubbed tapes

NORM

 

 

 

NOTES:

●“HI FI L j h R” should normally be selected. In this mode, Hi-Fi stereo tapes are played back in stereo, and the normal audio track is played back automatically for tapes with only normal audio.

●For instructions on recording stereo and bilingual programmes, refer to page 26.

●“O.S.D.” must be set to “ON” or the on-screen displays will not appear ( pg. 49).

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection To connect to a TV with S-VIDEO/AUDIO in connectorsSelect your country Auto Set Up12 EN Turn on the recorderOn the front display panel Perform Auto Set UpSelect the language Confirm/Set video channelPress rt to select CH - and press OK or e Perform Preset Download14 EN Set the video channelJust Clock Language for the on-screen display16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic PlaybackActivate frame-by-frame playback Slow MotionHigh-Speed Turbo Search Pause during playbackSkip Search 22 ENVariable Speed Search Index SearchSoundtrack Selection Next Function MemoryRepeat Playback Manual Tracking24 EN Tape Remaining Time Instant Timer Recording ITRReceiving Stereo and Bilingual Programmes Engage the S-VHS ET mode26 EN Super VHS ET S-VHS ETRecording Playback28 EN Access the Showview screenAccess the Showview Program screen Before performing the Showview Timer ProgrammingEnter the programme title Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer mode30 EN Express Timer ProgrammingPress PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel positionSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 32 ENAccess the Programme Check screen/display Disengage the timer modeCancel or change a programme Return to the timer modeOverlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modifyBefore performing the following steps Select the L-2 Select modeRecording mode Programme Recording36 EN NavigationSelect a programme Navigation PlaybackProgramme Navigation Screen Load a recorded cassetteSelect the programme 38 ENEdit Programme Title Example Enter JVC News Entering CharacterDelete Tape Data Delete the tape data40 EN Edit From a CamcorderStart the source player Set the input mode of recording deckAnother Video Recorder Advantages of S-VHS video recordersOutput/Input Set Decoder connector Select and L-2 Input SettingSimple Connections Connecting To a Satellite ReceiverPerfect Connections Set the tuner Select the input mode46 EN Connect the decoderMake connections Connecting/Using a Stereo SystemSelect the mode setting Mode SetAccess the Mode Set screen Select the modeClear picture reproduction is also linked to this function Using this video recorder as the source player for editingRecorder is powered back on With old tapes and rental cassettesFunction  pg , set PROG. Navigation to OFF On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode 50 ENMode setting Correction to the luminance signal to enhance detailIndicator lights up on the front display panel S-VHS recording mode is selectedColour System 52 ENEnter the Guide Program number Showview System SetupGuide Program Number Set Guide Program NumberAuto Channel Set Access the Auto Channel Set screenTuner Set 54 ENPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 56 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 58 ENSet Stations a Station Name TV Station And ID List60 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data62 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel SetPower Recording 64 ENOther Problems Playback 66 ENLines VHS Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Scan system68 EN Memo 70 EN
Top Page Image Contents