JVC HR-S7950EU specifications Programme Recording, Select the L-2 Select mode, Recording mode

Page 35

EN 35

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the recorder’s AV2 (L-2) IN/DECODER connector and programme the timer on the satellite receiver. The recorder starts or stops recording by the signals input from the satellite receiver. After recording, the recorder’s power shuts off automatically.

ATTENTION

●Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver’s power is turned on.

●If you have connected another appliance other than a satellite receiver to the AV2 (L-2) IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the recorder will start recording when the connected appliance’s power is turned on.

●Automatic Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

●Make sure the satellite receiver is connected to the recorder’s AV2 (L-2) IN/DECODER connector. ( pg. 44, 45)

●Programme the timer on the satellite receiver.

●Insert a cassette with the safety tab in place.

A Select the L-2 SELECT mode.

Set “L-2 SELECT” to “A/V” or “SAT” ( pg. 43).

● When you select “SAT”, refer to “IMPORTANT” on page 44.

B Set the tape speed.

Press SP/LP/EP (p).

● It is not possible to select EP mode if “COLOUR SYSTEM” is

set to “MESECAM”. ( pg. 52)

C Engage the Automatic Satellite Programme

Recording mode.

“ “indicator

Press and hold SAT# for about 2 seconds. The ““ indicator lights up and the recorder turns off automatically.

NOTES:

●To disengage the Automatic Satellite Programme Recording mode, press SAT#. The ““ indicator goes off.

●If the recorder’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

●In step 3, if the ““ indicator does not light but instead blinks quickly even though your satellite receiver’s power is off, Automatic Satellite Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Express Timer Programming” ( pg. 30) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

●The ““ indicator blinks while Automatic Satellite Programme Recording is in progress.

●For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

●Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

●Pressing the recorder’s 1 button while Automatic Satellite Programme Recording is in progress turns off the recorder’s power and disengages the Automatic Satellite Programme Recording mode.

●If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different tape speeds for each programme.

●Depending on the type of satellite receiver, the recorder may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

●If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the recorder will not

start Automatic Satellite Programme Recording even though the ““ indicator blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

●You can also record a programme from your cable system in the same way if the system has a timer.

●The B.E.S.T. system ( pg. 27) does not work while Automatic Satellite Programme Recording is in progress.

●Just Clock ( pg. 60) does not work when the Automatic Satellite Programme Recording mode is engaged.

●When the Automatic Satellite Programme Recording mode is engaged, or the recorder’s power is turned off after Automatic Satellite

Programme Recording is finished, the recorder will not enter the Timer mode even though “AUTO TIMER” is set to “ON” ( pg. 49).

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Connector coverRear View Front Display Panel ON-SCREEN Display Remote Control Operating JVC TVs How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection To connect to a TV with S-VIDEO/AUDIO in connectorsSelect your country Auto Set Up12 EN Turn on the recorderOn the front display panel Perform Auto Set UpSelect the language Confirm/Set video channelPress rt to select CH - and press OK or e Perform Preset Download14 EN Set the video channelJust Clock Language for the on-screen display16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic PlaybackActivate frame-by-frame playback Slow MotionHigh-Speed Turbo Search Pause during playbackSkip Search 22 ENVariable Speed Search Index SearchSoundtrack Selection Next Function MemoryRepeat Playback Manual Tracking24 EN Tape Remaining Time Instant Timer Recording ITRReceiving Stereo and Bilingual Programmes Engage the S-VHS ET mode26 EN Super VHS ET S-VHS ETRecording Playback28 EN Access the Showview screenAccess the Showview Program screen Before performing the Showview Timer ProgrammingEnter the programme title Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer mode30 EN Express Timer ProgrammingPress PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel positionSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 32 ENAccess the Programme Check screen/display Disengage the timer modeCancel or change a programme Return to the timer modeOverlapping programmes blink on the TV screen Cancel or change programme settingConfirm the overlapping programmes Select the programme to modifyBefore performing the following steps Select the L-2 Select modeRecording mode Programme Recording36 EN NavigationSelect a programme Navigation PlaybackProgramme Navigation Screen Load a recorded cassetteSelect the programme 38 ENEdit Programme Title Example Enter JVC News Entering CharacterDelete Tape Data Delete the tape data40 EN Edit From a CamcorderStart the source player Set the input mode of recording deckAnother Video Recorder Advantages of S-VHS video recordersOutput/Input Set Decoder connector Select and L-2 Input SettingSimple Connections Connecting To a Satellite ReceiverPerfect Connections Set the tuner Select the input mode46 EN Connect the decoderMake connections Connecting/Using a Stereo SystemSelect the mode setting Mode SetAccess the Mode Set screen Select the modeClear picture reproduction is also linked to this function Using this video recorder as the source player for editingRecorder is powered back on With old tapes and rental cassettesFunction  pg , set PROG. Navigation to OFF On the remote control, or press 7 on the recorderEntire programme while timer-recording in SP mode 50 ENMode setting Correction to the luminance signal to enhance detailIndicator lights up on the front display panel S-VHS recording mode is selectedColour System 52 ENEnter the Guide Program number Showview System SetupGuide Program Number Set Guide Program NumberAuto Channel Set Access the Auto Channel Set screenTuner Set 54 ENPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 56 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 58 ENSet Stations a Station Name TV Station And ID List60 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data62 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel SetPower Recording 64 ENOther Problems Playback 66 ENLines VHS Signal-to-noise ratio 45 dB Horizontal resolutionMemory backup time Approx min Scan system68 EN Memo 70 EN
Top Page Image Contents