JVC HR-S9400EE specifications Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 10

10ENINITIALSETTINGS(cont.)

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

 

 

 

8

•• • • • ••

•• • • • ••

• •

• •

• •

• •

 

 

 

STOP/EJECT

2

1 2 3

4

5

6

7 8 9

04

TV PROG

3

OK

1

TEST SIGNAL

The channel on which the screen to the left appear clearly in step 2 is your Video Channel.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable or AV cable (AV connection) or via the provided RF cable, the provided S-Video cable and the provided audio cable (S-VIDEO connection) – Go to "With AV or S-VIDEO Connection" on next page.

With RF Connection

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

ACCESS VIDEO CHANNEL SET MODE

 

Hold down STOP/EJECT on the recorder until the

1

display panel shows the following.

 

 

 

 

 

 

 

 

2

SET VIDEO CHANNEL

Set your TV to UHF channel 36.

 

 

 

 

● If the two vertical white bars appear clearly on the

 

 

screen as shown in the illustration at bottom left,

 

 

 

press OK and then go to step 3.

 

● If the two vertical white bars do not appear clearly,

 

 

 

press TV PROG + or – to set the video recorder to a

 

 

 

vacant channel between 22 and 69 which is not

 

 

 

occupied by any local station in your area.

 

 

(Ex.) If channel 50 is available in your area

 

 

 

 

 

 

 

 

 

 

Then set your TV to UHF channel 50 and check if the two vertical white bars appear clearly on the screen; if so, press OK and then go to step 3. If not, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

To view picture signals from the video recorder, set your TV to the Video Channel.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HR-S9400EE Safety Precautions Safety FirstMoisture Condensation Basic Connections Check ContentsEN Installing Your NEW Reco Rder Situate RecorderIf TV has no 21-pin Scart connector AV1 OUT SwitchINS Talling YO UR NEW R Ecorder Video ConnectionConnect Recorder to TV For TV sets with an S-VIDEO input terminal Back of TV Back of RecorderNitial Sett Ings Auto Set UpStart Auto SET UP Auto Channel SetLanguage Set Video Channel Set Access Video Channel SET ModeEN Initial Settings SET Video ChannelWith AV or S-VIDEO Connection Exit Video Channel SET ModeSelect TV System Major CountriesSET Date and Time Clock SetTurn the Recorder on Start Clock OperationOn-Screen Displays ENABLE/DISABLE ON-SCREEN Display14 3 Basic PlaybackPause During Playback Playback FeaturesActivate HIGH-SPEED Search Activate SLOW-MOTION PlaybackTracking Adjust TrackingOverride Automatic ManuallyInstant ReView Activate Instant ReviewIndex Search Mesecam PlaybackSoundtrack Selection Activate SpatializerSpatializer During PlaybackActivate Scene Finder SET A/B Code SwitchRE-SUPPLY Power Stop Scene FinderTimeScan Audio signal during TimeScanTime Scan Indicator Variable-Speed Search/ Reverse PlayTimeScan Audio TimeScanSpeed SP Speed LP Audio output Basic Recording Recording Features EN Recording VHS Super VHS and VHSLocate Start Point Engage RECORD-PAUSE ModeLevel Resume RecordingSwitch REC System switchPAL/SECAM Playback and Recording Recording Input Signal Conversion Timer Recording SetupAccess Main Menu Screen Make List of Stored Station Names Channel PositionsClose Menu Access Guide Prog SET ScreenNumber If you already know the Guide Program number for a stationEN Timer Recording Timer RecordingOn Next Satellite Tuner Users Press TIMER. The recorder turns off automaticallyTo timer-record a satellite broadcast using Showview Press OK Repeat steps 1-5for each additional programmePress Start +/-. If you’re just starting out, P1 appears Regular Timer ProgrammingPress Stop +/- to enter the time you want recording to stop Engage RECORDER’S Timer ModePress TV Prog + Revise Programme Access Mode SETAccess Programme InformationVPS Recording Timer WarningPress Display or Start + again to return to normal display SET TV Brand Code TV Multi Brand Remote ControlControl Your TV Using Additional Buttons TRY Operating TVTRY Operating Satellite Tuner Satellite Tuner MultiSET Satellite Tuner Brand Code Satellite Tuner Brand CodeEditing Editing Mode SettingPreparation For Editing Advantages Of S-VHS Video RecordersWhen using front panel input connectors To Select The External Input ModeWhen using rear panel input connectors Connector On display panelEdit To Or From Another Video Recorder Recorder If another recorder has no 21-pin Scart connectorPlayer Recorder PlayerStart Camcorder SET RECORDER’S Input ModeEdit From a Camcorder Start RecorderEngage Audio Dubbing SET Input ModeAudio Dubbing Start DubbingLocate END Point Reset the CounterEN Editing Start Editing END Insert EditingPrepare for Editing Access R.A. Edit ScreenRandom As- semble Editing Load Source CassetteStart R.A. Edit Locate EDIT-IN PointLocate EDIT-OUT Point To Make CorrectionsEND R.A. Edit RM-V704 Multi-Brand R.A. Edit Controller Not providedSET Jlip ID Number Access Jlip ID NO. SET ScreenTerminal Jlip Joint Level Interface Protocol Connector Return to Normal ScreenSystem Connection ToStereo EN System ConnectionsTuner SET Perform Auto Channel SETView Confirmation Screen Press Push JOGStoring Channels Manually Major Countries TV SystemDelete Channel Access Manual CH. SET ScreenSelect Item Close ConfirmationSelect NEW Station Switch StationsPerform Tuning Select Channel toTV Station And ID List Station NameConnection, set the TV to its AV mode If you are using the AV or S-VIDEOSet the TV receiver to the Video Timer again RecordingOther Problems OubleshootingÄ remain lit on the display panel. Is there a problem? Questions and Answer S E NIndex Front ViewRear View How To Use Installing BatteriesEN Index Specifications Backup time becomes shorter as the units internal partsHR-S9400EE
Top Page Image Contents