JVC HR-S9400EE specifications Auto Set Up, Start Auto SET UP, Nitial Sett Ings, Auto Channel Set

Page 8

8EN

INITIALSETTINGS

Auto Set Up

Auto Channel Set

When the button on the recorder/remote control is pressed for the first time to power on the recorder after you plug the mains power cord into a mains outlet, the Auto Set Up function sets the tuner channels automatically.

You can refer to the front display panel and/or the on-screen display to perform this procedure.

 

 

 

8

•• • • • ••

•• • • • ••

• •

• •

• •

• •

Before starting, make sure of the following:

●The TV aerial cable should be connected to the recorder.

●The recorder's mains power cord should be connected to a mains outlet. (☞ pg. 4)

●If you want to use the on-screen display, the TV should be set to its AV mode (with AV or S-VIDEO connection

☞pg. 4 or 6) or UHF channel 36 (with RF connection

☞pg. 4).

2

1 2 3

4

5

6

ATTENTION

Once you have performed Auto Set Up, even if the recorder's memory backup has expired, all the stored stations remain in the recorder's memory and the recorder will not perform Auto Set Up again.

If you have moved to a different area or a new station starts broadcasting in your area, perform tuner setting. (☞ pg. 51)

1

START AUTO SET UP

Press .

●The Auto Set Up function scans all the channels that are receivable by your recorder. It then automatically assigns each receivable channels to the TV PROG buttons. It skips non-receivable channels.

●As Auto Set Up progresses, the " " mark on the screen moves from left to right.

●After you perform Auto Set Up, if the tuner channels have not been set properly or if "CH – –" is displayed on the front display panel, make sure that the aerial cable is connected to the recorder properly and turn off the recorder power once, and turn the power back on to try Auto Set Up again.

●If there is a power cut, or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the recorder power once and try again.

DO NOT press any button on the recorder or remote control while Auto Set Up is in progress.

 

АВТО УСТАНОВКА

 

 

On-Screen Display

ПОЖАЛУЙСТА, ПОДОЖДИТЕ

 

 

 

 

 

0

+

+

+

+

[MENU] : ВЫХОД

During Auto Set Up

"ПОЖАЛУЙСТА, ПОДОЖДИТЕ", blinks on the screen and "Auto" blinks on the front display panel.

TV Screen

When Auto Set Up is completed, the lowest position number will appear on the front display panel.

Front Display Panel

NOTES:

●If you have connected your TV to the recorder with RF connection and the on-screen display appearing on UHF channel 36 looks distorted, refer to the front display panel.

●If you want to set the tuner manually such as to add or skip channels, to swap channel positions, to fine-tune channels or to set station names (ID – ☞ p. 55), ☞ pg. 52 – 55.

●If no sound accompanies the picture on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels. ☞ "TV System Selection – When you see the picture but hear no audio" on page 53.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents HR-S9400EE Safety Precautions Safety FirstMoisture Condensation Check Contents EN Installing Your NEW Reco RderBasic Connections Situate RecorderIf TV has no 21-pin Scart connector AV1 OUT SwitchVideo Connection Connect Recorder to TVINS Talling YO UR NEW R Ecorder For TV sets with an S-VIDEO input terminalBack of TV Back of RecorderAuto Set Up Start Auto SET UPNitial Sett Ings Auto Channel SetLanguage Set Access Video Channel SET Mode EN Initial SettingsVideo Channel Set SET Video ChannelExit Video Channel SET Mode Select TV SystemWith AV or S-VIDEO Connection Major CountriesClock Set Turn the Recorder onSET Date and Time Start Clock Operation14 3 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Basic PlaybackPlayback Features Activate HIGH-SPEED SearchPause During Playback Activate SLOW-MOTION PlaybackAdjust Tracking Override AutomaticTracking ManuallyActivate Instant Review Index SearchInstant ReView Mesecam PlaybackActivate Spatializer SpatializerSoundtrack Selection During PlaybackSET A/B Code Switch RE-SUPPLY PowerActivate Scene Finder Stop Scene FinderAudio signal during TimeScan Time Scan IndicatorTimeScan Variable-Speed Search/ Reverse PlaySpeed SP Speed LP Audio output TimeScanTimeScan Audio Basic Recording Recording Features EN Recording VHS Super VHS and VHSEngage RECORD-PAUSE Mode LevelLocate Start Point Resume RecordingPAL/SECAM Playback and Recording REC System switchSwitch Recording Input Signal Conversion Setup Access Main Menu ScreenTimer Recording Make List of Stored Station Names Channel PositionsAccess Guide Prog SET Screen NumberClose Menu If you already know the Guide Program number for a stationOn Next Timer RecordingEN Timer Recording Press TIMER. The recorder turns off automatically To timer-record a satellite broadcast using ShowviewSatellite Tuner Users Press OK Repeat steps 1-5for each additional programmePress Stop +/- to enter the time you want recording to stop Regular Timer ProgrammingPress Start +/-. If you’re just starting out, P1 appears Press TV Prog + Timer ModeEngage RECORDER’S Access Mode SET Access ProgrammeRevise Programme InformationPress Display or Start + again to return to normal display Timer WarningVPS Recording TV Multi Brand Remote Control Control Your TV Using Additional ButtonsSET TV Brand Code TRY Operating TVSatellite Tuner Multi SET Satellite Tuner Brand CodeTRY Operating Satellite Tuner Satellite Tuner Brand CodeEditing Mode Setting Preparation For EditingEditing Advantages Of S-VHS Video RecordersTo Select The External Input Mode When using rear panel input connectorsWhen using front panel input connectors Connector On display panelEdit To Or From Another Video Recorder If another recorder has no 21-pin Scart connector PlayerRecorder Recorder PlayerSET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderSET Input Mode Audio DubbingEngage Audio Dubbing Start DubbingEN Editing Reset the CounterLocate END Point Start Editing END Insert EditingAccess R.A. Edit Screen Random As- semble EditingPrepare for Editing Load Source CassetteLocate EDIT-IN Point Locate EDIT-OUT PointStart R.A. Edit To Make CorrectionsEND R.A. Edit RM-V704 Multi-Brand R.A. Edit Controller Not providedAccess Jlip ID NO. SET Screen Terminal Jlip Joint Level Interface Protocol ConnectorSET Jlip ID Number Return to Normal ScreenConnection To StereoSystem EN System ConnectionsPerform Auto Channel SET View Confirmation ScreenTuner SET Press Push JOGStoring Channels Manually Major Countries TV SystemAccess Manual CH. SET Screen Select ItemDelete Channel Close ConfirmationSwitch Stations Perform TuningSelect NEW Station Select Channel toTV Station And ID List Station NameSet the TV receiver to the Video If you are using the AV or S-VIDEOConnection, set the TV to its AV mode Timer again RecordingOther Problems OubleshootingÄ remain lit on the display panel. Is there a problem? Questions and Answer S E NIndex Front ViewRear View EN Index Installing BatteriesHow To Use Specifications Backup time becomes shorter as the units internal partsHR-S9400EE

HR-S9400EE specifications

The JVC HR-S9400EE is a versatile and highly regarded Super VHS (S-VHS) VCR that has been a favorite among video enthusiasts and professionals. Released in the 1990s, it is celebrated for its cutting-edge technology and a plethora of features that cater to both casual users and avid videographers.

One of the standout characteristics of the HR-S9400EE is its Super VHS playback capability. This allows for improved video quality compared to standard VHS, providing sharper images and enhanced color fidelity. The unit incorporates a digital noise reduction system, which significantly minimizes artifacts and enhances the overall clarity of the recorded footage. This technology is particularly important for capturing high-quality home videos or professional content.

The JVC HR-S9400EE also boasts a unique 3D Y/C separation system, which effectively separates the luminance (Y) and chrominance (C) signals, leading to higher resolution and improved picture quality. Additionally, it includes a built-in TBC (Time Base Corrector) that ensures smooth playback by correcting video timing errors, making it particularly useful for older tapes that may have suffered from signal degradation.

Another notable feature is its extensive range of playback formats. The HR-S9400EE can handle not only S-VHS tapes but also standard VHS and VHS-C formats, providing unparalleled flexibility for users with diverse collections. The device comes equipped with a remote control for convenient operation, making it easy to navigate through menus and adjust settings without hassle.

The unit also features stereo audio playback, delivering a rich sound experience that complements its visual capabilities. For those interested in dubbing or transferring tapes, the JVC HR-S9400EE offers high-quality recording options, making it a valuable asset for archiving precious memories.

In terms of design, the HR-S9400EE is built with reliability and user-friendliness in mind. Its intuitive layout and well-placed buttons make it simple to operate, while the sturdy construction ensures that it can withstand regular use without compromising performance.

Overall, the JVC HR-S9400EE VCR stands out as a high-quality option for anyone seeking superior video recording and playback capabilities. Its impressive array of features and technologies makes it a timeless choice for preserving and enjoying video content, even in an age dominated by digital formats.
Top Page Image Contents