JVC HR-S9400EE specifications VPS Recording, Timer Warning

Page 35

DISPLAY

 

2

 

1

2

3

4

5

6

7

8

9

CANCEL

0

4

 

 

START+

3

1

EN35

VPS Recording

Now available from some TV stations, VPS (Video Programme System) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over advertised times you preset in the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed.

NOTES:

● When you manually enter programmes (regular timer programming), set the start time (VPS time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

● VPS recording is not possible in areas where no TV station transmits VPS signals.

● VPS recording is also possible when a satellite tuner or a cable system is connected to the AV2 IN connector on your recorder.

● VPS recording is also possible via the AV1 IN/OUT connector and the front panel connectors.

How to check if the station being received transmits a

VPS signal

1 Press DISPLAY until the channel position appears on the display panel.

2 Hold down START + for about 5 seconds.

● " " appears blinking on the display panel.

If a VPS signal is detected from the station, " " will stop blinking.

If no VPS signal is detected from the station, " " will blink at a slower rate.

3 Press DISPLAY or START + again to return to normal display.

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on screen to tell you that the record- ing is to start in 5 minutes.

–WARNING– TIMER RECORDING

TO START SOON

[CANCEL]

NOTES:

●The warning only appears if you’re not in the Timer mode at that time.

●If this recorder is being used as the player for tape dubbing, the warning screen is recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press CANCEL.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents HR-S9400EE Safety First Safety PrecautionsMoisture Condensation Situate Recorder Check ContentsEN Installing Your NEW Reco Rder Basic ConnectionsAV1 OUT Switch If TV has no 21-pin Scart connectorFor TV sets with an S-VIDEO input terminal Video ConnectionConnect Recorder to TV INS Talling YO UR NEW R EcorderBack of Recorder Back of TVAuto Channel Set Auto Set UpStart Auto SET UP Nitial Sett IngsLanguage Set SET Video Channel Access Video Channel SET ModeEN Initial Settings Video Channel SetMajor Countries Exit Video Channel SET ModeSelect TV System With AV or S-VIDEO ConnectionStart Clock Operation Clock SetTurn the Recorder on SET Date and Time14 3 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Playback BasicActivate SLOW-MOTION Playback Playback FeaturesActivate HIGH-SPEED Search Pause During PlaybackManually Adjust TrackingOverride Automatic TrackingMesecam Playback Activate Instant ReviewIndex Search Instant ReViewDuring Playback Activate SpatializerSpatializer Soundtrack SelectionStop Scene Finder SET A/B Code SwitchRE-SUPPLY Power Activate Scene FinderVariable-Speed Search/ Reverse Play Audio signal during TimeScanTime Scan Indicator TimeScanSpeed SP Speed LP Audio output TimeScanTimeScan Audio Basic Recording Recording Features VHS Super VHS and VHS EN RecordingResume Recording Engage RECORD-PAUSE ModeLevel Locate Start PointPAL/SECAM Playback and Recording REC System switchSwitch Recording Input Signal Conversion Make List of Stored Station Names Channel Positions SetupAccess Main Menu Screen Timer RecordingIf you already know the Guide Program number for a station Access Guide Prog SET ScreenNumber Close MenuOn Next Timer RecordingEN Timer Recording Press OK Repeat steps 1-5for each additional programme Press TIMER. The recorder turns off automaticallyTo timer-record a satellite broadcast using Showview Satellite Tuner UsersPress Stop +/- to enter the time you want recording to stop Regular Timer ProgrammingPress Start +/-. If you’re just starting out, P1 appears Press TV Prog + Timer ModeEngage RECORDER’S Information Access Mode SETAccess Programme Revise ProgrammePress Display or Start + again to return to normal display Timer WarningVPS Recording TRY Operating TV TV Multi Brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSatellite Tuner Brand Code Satellite Tuner MultiSET Satellite Tuner Brand Code TRY Operating Satellite TunerAdvantages Of S-VHS Video Recorders Editing Mode SettingPreparation For Editing EditingConnector On display panel To Select The External Input ModeWhen using rear panel input connectors When using front panel input connectorsEdit To Or From Another Video Recorder Recorder Player If another recorder has no 21-pin Scart connectorPlayer RecorderStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderStart Dubbing SET Input ModeAudio Dubbing Engage Audio DubbingEN Editing Reset the CounterLocate END Point END Insert Editing Start EditingLoad Source Cassette Access R.A. Edit ScreenRandom As- semble Editing Prepare for EditingTo Make Corrections Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditRM-V704 Multi-Brand R.A. Edit Controller Not provided END R.A. EditReturn to Normal Screen Access Jlip ID NO. SET ScreenTerminal Jlip Joint Level Interface Protocol Connector SET Jlip ID NumberEN System Connections Connection ToStereo SystemPress Push JOG Perform Auto Channel SETView Confirmation Screen Tuner SETMajor Countries TV System Storing Channels ManuallyClose Confirmation Access Manual CH. SET ScreenSelect Item Delete ChannelSelect Channel to Switch StationsPerform Tuning Select NEW StationStation Name TV Station And ID ListSet the TV receiver to the Video If you are using the AV or S-VIDEOConnection, set the TV to its AV mode Recording Timer againOubleshooting Other ProblemsQuestions and Answer S E N Ä remain lit on the display panel. Is there a problem?Front View IndexRear View EN Index Installing BatteriesHow To Use Backup time becomes shorter as the units internal parts SpecificationsHR-S9400EE

HR-S9400EE specifications

The JVC HR-S9400EE is a versatile and highly regarded Super VHS (S-VHS) VCR that has been a favorite among video enthusiasts and professionals. Released in the 1990s, it is celebrated for its cutting-edge technology and a plethora of features that cater to both casual users and avid videographers.

One of the standout characteristics of the HR-S9400EE is its Super VHS playback capability. This allows for improved video quality compared to standard VHS, providing sharper images and enhanced color fidelity. The unit incorporates a digital noise reduction system, which significantly minimizes artifacts and enhances the overall clarity of the recorded footage. This technology is particularly important for capturing high-quality home videos or professional content.

The JVC HR-S9400EE also boasts a unique 3D Y/C separation system, which effectively separates the luminance (Y) and chrominance (C) signals, leading to higher resolution and improved picture quality. Additionally, it includes a built-in TBC (Time Base Corrector) that ensures smooth playback by correcting video timing errors, making it particularly useful for older tapes that may have suffered from signal degradation.

Another notable feature is its extensive range of playback formats. The HR-S9400EE can handle not only S-VHS tapes but also standard VHS and VHS-C formats, providing unparalleled flexibility for users with diverse collections. The device comes equipped with a remote control for convenient operation, making it easy to navigate through menus and adjust settings without hassle.

The unit also features stereo audio playback, delivering a rich sound experience that complements its visual capabilities. For those interested in dubbing or transferring tapes, the JVC HR-S9400EE offers high-quality recording options, making it a valuable asset for archiving precious memories.

In terms of design, the HR-S9400EE is built with reliability and user-friendliness in mind. Its intuitive layout and well-placed buttons make it simple to operate, while the sturdy construction ensures that it can withstand regular use without compromising performance.

Overall, the JVC HR-S9400EE VCR stands out as a high-quality option for anyone seeking superior video recording and playback capabilities. Its impressive array of features and technologies makes it a timeless choice for preserving and enjoying video content, even in an age dominated by digital formats.
Top Page Image Contents