JVC HR-J430KR manual Simple Recording

Page 13

Simple Recording

PAUSE

6

q

REC

°5

CH

PLAY

ENTER

	1	2	3
NUMBER	4	5	6
NUMBER
	7	8	9
		0

CH

SP/EP

PLAY

PAUSE

REC

STOP

13

1		LOAD A CASSETTE
		Make sure the record safety tab is intact. If not, cover the
		hole with adhesive tape before inserting the cassette.
		SELECT RECORDING
2		CHANNEL
		Press CH5°. Or press the appropriate NUMBER keys,
		then press ENTER. (The channel changes after a few
		seconds whether you press ENTER or not.)
3		SET TAPE SPEED
3		Press SP/EP to set the recording speed.
4		START RECORDING
		Press and hold REC and press PLAY on the remote
		control, or press REC on the VCR's front panel.

		B.E.S.T. takes place at the beginning of both the first
		SP and the first EP recording after inserting the
		cassette (☞ pg. 22).


		PAUSE/RESUME
5		RECORDING
5		Press PAUSE. Press PLAY to resume recording.
6		STOP RECORDING
		Press STOP or STOP/EJECT. Then press STOP/EJECT to
		remove the cassette.

Accidental erasure prevention

●To prevent accidental recording on a recorded cassette, remove its record safety tab.

To record on it later, cover the hole with adhesive tape.

Record safety tab

Image 13

Contents HR-J430KR Do not place the VCR Dear CustomerContents Basic Connections SET Date and Time ClockMake Corrections Tuner Return to Normal Screen Perform Auto Channel SETAccess AFC Screen Access Tuner SET ScreenMake Selection Store Desired ChannelAccess Main Menu Screen Code SetupAccess G-CODE SET-UP Screen Access Initial SET ScreenAccess Guide Channel SET Screen Input Guide Channel NumberInput Receiving Channel Number Return to G-CODE SET UP ScreenReturn to Normal Load a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Activate FRAME-BY Frame Playback Pause During PlaybackStill Picture/Frame-By- Frame Playback Slow Motion/ Reverse Slow MotionActivate HIGH-SPEED Search Activate VARIABLE-SPEED SearchVariable-Speed Search Reverse Play High-Speed SearchAdjust Manual Tracking Engage Manual Tracking ModeRE-ENGAGE Automatic Tracking Manual TrackingAccess Superimpose Access Function SETSuperimpose Skip Over Unwanted Sections Access Distant CodeStart Repeat Stop RepeatActivate Counter Activate Instant ReviewMemory Return to Counter Position ZeroRelation to B Beginning or E End shows you where you are on Tape Position IndicatorPress REW, then press Timer within 2 seconds Next-Function MemorySelect Mode Access B.E.S.T. Picture System ScreenS.T. Picture System PreparationPress and hold REC RecordingQuality of the tape Use, then recording Begins with the picture Level optimizedTape in use PlaybackReset Counter to Zero Engage TV ModeRecording Select Channel for ViewingEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press RECAccess G-CODE Screen Code Timer ProgrammingEnter G-CODE Number CHECK/CORRECT Input Engage Timer ModeData Access ON-SCREEN On-Screen Timer ProgrammingAccess Program SET Screen MenuExample SET Program InformationCancel a Program Disengage TimerRE-ENGAGE Timer Check And Cancel ProgramsAuto SP/EP Timer Access Auto SP/EPPlace the arrow next to Auto SP/EP Timer by Pressing CH 5 or Push JOG 5, then press OKAuto Timer Access Auto Timer19, 20 Special FeaturesEdit From a Camcorder Edit To Or From Another SET RECORDER’S Input ModeLoad Cassettes Control Two JVC VCRsPrepare for Editing Random As- semble EditingStart R.A. Edit END R.A. EditCassette gets stuck partway TroubleshootingRe-perform the G-Code setup Doesn’t work properly Timer againWhen scanning channels, some Has not been programmed correctly Cassette is automaticallyQuestions and Answers Maximum recording time 210 min. with ST-210 video EIA monochrome signal630 min. with ST-210 video Frequency-synthesized tunerIndex Ramdom Assemble Editing connector pgFront Display Panel Remote Control ProvidedHR-J430KR