JVC HR-J430KR manual Special Features, 19, 20

Page 33

● The POWER, TV/VIDEO, CH5°, VOL +/– and NUMBER keys on the remote can all be used to operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.

● To return the remote to VCR control, set the TV/VCR switch to VCR.

NOTE:

Depending on the kind of TV, there may be cases where some or all functions cannot be operated using the remote control.

First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.

4

● Once you have set the remote control to operate the TV, you don’t have to repeat this step until you replace your remote control’s batteries.

OPERATE TV

Refer to the chart below. While holding down POWER, enter your TV’s brand code using the NUMBER keys, then press STOP.

SET TV BRAND CODE

2 Set the TV/VCR switch on the VCR's remote control to TV.

3

Turn the power on using the TV's remote control.

SET REMOTE CONTROL MODE

1

TV Multi-Brand Remote Control

The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below. Some TV brands have more than one code. If the TV will not function with one code, try entering another.

TURN ON THE TV

SPECIALFEATURES

POWER

ENTER

	1	2	3
NUMBER	4	5	6
NUMBER
	7	8	9
		0

CH

VOL. +/-

TV/VCR

STOP

TV BRAND NAME	BRAND CODE
JVC	01
PHILIPS	03
PHILICO	05
HITACHI	05
SHARP	06
TOSHIBA	07
MITSUBISHI	08
PHILICO/DAEWOO	09
PACKARD BELL	09
KIOTE/DAEWOO	09
DAEWOO	10
SAMSUNG	11
GOLDSTAR	12
RCA	14
PANASONIC	15, 16
SONY	18
ZONDA	19, 20, 21
AKAWA	21, 22
ELECTRA	23

33

Image 33

Contents HR-J430KR Do not place the VCR Dear CustomerContents Basic Connections Clock SET Date and TimeMake Corrections Tuner Return to Normal Screen Perform Auto Channel SETAccess AFC Screen Access Tuner SET ScreenMake Selection Store Desired ChannelAccess Main Menu Screen Code SetupAccess G-CODE SET-UP Screen Access Initial SET ScreenAccess Guide Channel SET Screen Input Guide Channel NumberReturn to G-CODE SET UP Screen Input Receiving Channel NumberReturn to Normal Load a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Activate FRAME-BY Frame Playback Pause During PlaybackStill Picture/Frame-By- Frame Playback Slow Motion/ Reverse Slow MotionActivate HIGH-SPEED Search Activate VARIABLE-SPEED SearchVariable-Speed Search Reverse Play High-Speed SearchAdjust Manual Tracking Engage Manual Tracking ModeRE-ENGAGE Automatic Tracking Manual TrackingAccess Function SET Access SuperimposeSuperimpose Skip Over Unwanted Sections Access Distant CodeStart Repeat Stop RepeatActivate Counter Activate Instant ReviewMemory Return to Counter Position ZeroRelation to B Beginning or E End shows you where you are on Tape Position IndicatorPress REW, then press Timer within 2 seconds Next-Function MemorySelect Mode Access B.E.S.T. Picture System ScreenS.T. Picture System PreparationPress and hold REC RecordingQuality of the tape Use, then recording Begins with the picture Level optimizedTape in use PlaybackReset Counter to Zero Engage TV ModeRecording Select Channel for ViewingEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press RECCode Timer Programming Access G-CODE ScreenEnter G-CODE Number Engage Timer Mode CHECK/CORRECT InputData Access ON-SCREEN On-Screen Timer ProgrammingAccess Program SET Screen MenuExample SET Program InformationCancel a Program Disengage TimerRE-ENGAGE Timer Check And Cancel ProgramsAuto SP/EP Timer Access Auto SP/EPPlace the arrow next to Auto SP/EP Timer by Pressing CH 5 or Push JOG 5, then press OKAuto Timer Access Auto Timer19, 20 Special FeaturesEdit From a Camcorder Edit To Or From Another SET RECORDER’S Input ModeLoad Cassettes Control Two JVC VCRsPrepare for Editing Random As- semble EditingStart R.A. Edit END R.A. EditCassette gets stuck partway TroubleshootingRe-perform the G-Code setup Doesn’t work properly Timer againWhen scanning channels, some Has not been programmed correctly Cassette is automaticallyQuestions and Answers Maximum recording time 210 min. with ST-210 video EIA monochrome signal630 min. with ST-210 video Frequency-synthesized tunerIndex Ramdom Assemble Editing connector pgFront Display Panel Remote Control ProvidedHR-J430KR